Danfoss VLT MSD 510 Operating Manual page 9

Operating Guide | VLT® Multiaxis Servo Drive MSD 510 System
9.2.1.8
9.2.1.9
9.2.1.10 Drive Speed Drops Sharply under Load
9.2.1.11 Brake not Releasing
9.2.1.12 Holding Brake not Holding the Servo Drive
9.2.1.13 Delayed Brake Engagement
9.2.1.14 Noises when Power-Off Brake is Engaged
9.2.1.15 LEDs not Lighting Up
9.2.1.16 Drive Protection Trips Immediately
9.2.2 Troubleshooting for the Servo System
9.2.2.1
9.2.2.2
9.2.2.3
9.2.2.4
9.2.2.5
9.2.2.6
9.2.2.7
9.2.2.8
9.2.2.9
9.2.2.10 UAUX Undervoltage (Error 0x3294/0x135)
9.2.2.11 Mains Phase Loss (Error 0x3130/0x12F)
9.2.2.12 Grounding Fault
9.2.2.13 Brake Resistor Error
9.2.2.14 Brake Chopper Error
9.2.2.15 Internal Fan Error
9.3 Error Codes
9.3.1 No error (0x0000 / 0x0)
9.3.2 Generic err (0x1000 / 0x100)
9.3.3 Overcurrent on output (0x2310 / 0x101)
9.3.4 High current overload (0x2311 / 0x15F)
9.3.5 I2T current overload (0x2312 / 0x160)
9.3.6 High power overload (0x2313 / 0x161)
9.3.7 PT power overload (0x2314 / 0x162)
9.3.8 Short circuit (0x2320 / 0x163)
9.3.9 Earth leakage (0x2330 / 0x151)
9.3.10 AUX overcurrent (0x2391 / 0x125)
9.3.11 AUX user limit current (0x2393 / 0x127)
9.3.12 AUX user limit current warning (0x2394 / 0x128)
9.3.13 AUX fuse failure (0x2395 / 0x129)
9.3.14 DC overcurrent trip (0x2396 / 0x15C)
9.3.15 Output power trip (0x2397 / 0x12B)
9.3.16 I2T overload motor (0x239B / 0x102)
Danfoss A/S © 2019.10
Vibration
Unusual Running Noises
LCP Display is Dark/Not Functioning
Open Power Fuses or Circuit Breaker Trip
DC-link Voltage Too High (Error 0x3210/0x103)
DC-link Voltage Too Low (Error 0x3220/0x104)
DC-link Overcurrent (Error 0x2396/0x15C)
DC link Overpower (Error 0x2313/0x161)
PT Power Overload (Error 0x2314/0x162)
UAUX Overcurrent (Error 0x2391/0x125)
UAUX Overvoltage (Error 0x3292/0x133)
Contents
165
165
165
165
166
166
166
166
166
167
167
167
168
168
168
169
169
169
169
170
170
170
170
171
171
171
171
172
172
172
172
172
173
173
173
173
174
174
174
174
174
175
AQ262450196490en-000101 / | 9