Danfoss VLT PROFINET MCA 120 Installation Manual
  1. Manuals
  2. Brands
  3. Danfoss Manuals
  4. DC Drives
  5. VLT PROFINET MCA 120
  6. Installation manual
Danfoss VLT PROFINET MCA 120 Installation Manual

Danfoss VLT PROFINET MCA 120 Installation Manual

Hide thumbs Also See for VLT PROFINET MCA 120:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Installation Guide
VLT® PROFINET MCA 120
VLT® AutomationDrive FC 361
1 Introduction
1.1 Purpose of this Installation Guide
This installation guide provides information for quick replacement of a VLT® PROFINET MCA 120 interface in the VLT® AutomationDrive
FC 361.
The installation guide is intended for use by qualified personnel. Users are assumed to be familiar with the VLT® drive, with PROFINET
technology, and with the PC or PLC used as a master in the system.
Read the instructions before installation and ensure that instructions for safe installation are observed.
1.2 Trademarks
®
VLT
is a registered trademark for Danfoss A/S.
Danfoss A/S © 2019.03
AN274237376992en-000101 / 130R0856 | 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VLT PROFINET MCA 120 and is the answer not in the manual?

Questions and answers

Related Manuals for Danfoss VLT PROFINET MCA 120

Summary of Contents for Danfoss VLT PROFINET MCA 120

  • Page 1 PC or PLC used as a master in the system. Read the instructions before installation and ensure that instructions for safe installation are observed. 1.2 Trademarks ® is a registered trademark for Danfoss A/S. Danfoss A/S © 2019.03 AN274237376992en-000101 / 130R0856 | 1...

  • Page 2: Safety Precautions

    Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors are fully discharged. Table 1: Discharge Time Voltage [V] Power range [kW (hp)] Minimum waiting time (minutes) 380–480 90–315 kW (125–450 hp) 2 | Danfoss A/S © 2019.03 AN274237376992en-000101 / 130R0856...

  • Page 3: Technical Data

    Shielding design type Aluminum foil + Cu braiding Application Plug type RJ 45 (IP20 or IP65/67)/M12 Table 3: Transmission Performance Requirements Relevant standard ISO/IEC 11801 Edition 2.0, IEC 61156 (minimum Category 5) Danfoss A/S © 2019.03 AN274237376992en-000101 / 130R0856 | 3...
  • Page 4 Installation Guide | VLT® PROFINET MCA 120 Technical Data Delay skew ≤20 ns/100 m Transfer impedance ≤50 m Ω/m at 10 MHz 4 | Danfoss A/S © 2019.03 AN274237376992en-000101 / 130R0856...

  • Page 5: Installation

    In all other combinations, the address switches have priority over the parameter setting. The station name is set based on the value in 15-40 FC Type, and a 3-digit number selected from the DIP settings. Danfoss A/S © 2019.03 AN274237376992en-000101 / 130R0856 | 5...
  • Page 6 Use the address switches to set the 253 different station names according to table Table 5: Host Names Setting Switch 12-08 Host Name +128 The station name change comes into effect at the next power-up. Read the station name in 12-08 Host Name. 6 | Danfoss A/S © 2019.03 AN274237376992en-000101 / 130R0856...

  • Page 7: Wiring Procedures

    3. Tie down the cable and route it with other control wires inside the unit. N O T I C E Do not strip the Ethernet cable. Ground the shielded Ethernet cables through the RJ45 connector on the PROFINET interface. Danfoss A/S © 2019.03 AN274237376992en-000101 / 130R0856 | 7...
  • Page 8 Installation Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies.

This manual is also suitable for:

Vlt automationdrive fc 361

Table of Contents