Keithley 4200A-SCS Reference Manual page 338

Model 4200A-SCS Parameter Analyzer Reference Manual
Parameters common to PMU operation modes
The following parameters are common to all PMU operation modes except DC Gnd. Brief
descriptions are provided here. Select the links to access additional information. The parameters are
listed in the order in which they appear in the All Parameters pane.
Parameter
Disable Outputs at Completion
page 6-72)
Current Spot Mean High
72)
Current Spot Mean Low
72)
Measure Current Range
73)
Low Range
Current Sample Waveform
6-75)
Voltage Spot Mean High
74)
Voltage Spot Mean Low
74)
Voltage Sample Waveform
6-75)
Report Timestamps
Report Status
Compensation Short Connection
page 6-79)
Compensation Load Line Effect
page 6-79)
Compensation DUT Resistance
page 6-79)
Max Voltage Estimator
79)
Voltage Threshold
Current Threshold
Power Threshold
4200A-901-01 Rev. C / February 2017
(on
(on page 6-
(on page 6-
(on page 6-
(on page 6-44)
(on page
(on page 6-
(on page 6-
(on page
(on page 6-75)
(on page 6-75)
(on
(on
(on
(on page 6-
(on page 6-79)
(on page 6-79)
(on page 6-80)
Description
When a test is complete, you can disable the outputs or leave them
enabled.
Makes current measurements on the amplitude. Available when the Test
Mode is set to Pulse I-V.
Makes current measurements on the base level. Available when the Test
Mode is set to Pulse IV.
The measure range determines the full-scale measurement span that is
applied to the signal.
Available when the Measure Range is set to Limited Auto. This sets the
minimum range that the instrument uses.
Makes current measurements on the waveform. Available when the Test
Mode is set to Waveform Capture.
Makes voltage measurements on the amplitude. Available when the Test
Mode is set to Pulse IV.
Makes voltage measurements on the base level. Available when the Test
Mode is set to Pulse IV.
Makes voltage measurements on the waveform. Available when the Test
Mode is set to Waveform Capture.
Available when the Test Mode is set to Waveform Capture. When Report
Timestamps is enabled, each measurement includes a timestamp and the
waveform is graphed (voltage/current versus time) in the Analyze graph.
When this option is selected, Clarius records measurement status
information when the test executes. A column of the Analyze spreadsheet
displays this information. Hover over a cell to review the information. For
PMU measurements, this information is also available as a 32-bit word. The
status code bit map is listed in
Use to enable or disable short connection compensation. Refer to
connection compensation (on page 5-30) for detail on setting up and using
connection compensation.
Use to enable or disable load-line effect compensation (LLEC). Refer to
Load-line effect compensation (LLEC) for the PMU
on setting up and using load-line effect compensation.
The DUT resistance value. Refer to
voltage across DUT (on page 5-61) for detail on calculating DUT resistance.
Only available in the Advanced Terminal Settings dialog box. The Maximum
Voltage Estimator is a tool that enables you to calculate the maximum
voltage and current based on the selected voltage range and the DUT
resistance value you type in. The estimator does not affect the pulse output.
The voltage threshold allows you to set a voltage threshold. If the threshold
is reached or exceeded, the present sweep is stopped. Testing continues
with any subsequent sweeps.
The current threshold allows you to set a threshold. If the threshold is
reached or exceeded, the present sweep is stopped. Testing continues with
any subsequent sweeps.
The power threshold allows you to set a power threshold. If the threshold is
reached or exceeded, the present sweep is stopped. Testing continues with
any subsequent sweeps.
Section 6: Clarius
pulse_fetch (on page 13-101).
(on page 5-34) for detail
DUT resistance determines pulse
PMU
6-69