Bi: Tm31 Signal Source For Terminal Do 1 / Tm31 S S Do 1; Bi: Tm15Di/Do Signal Source For Terminal Di/Do 2 / Tm15D S_Src Di/Do2; Bi: Tm15Di/Do Signal Source For Terminal Di/Do 3 / Tm15D S_Src Di/Do3; Bi: Tm15Di/Do Signal Source For Terminal Di/Do 4 / Tm15D S_Src Di/Do4 - Siemens SINAMICS DCM List Manual

p4031

BI: TM31 signal source for terminal DO 1 / TM31 s s DO 1

TM31 Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for the digital output DO 1 (X542.4, X542.5, X542.6) of Terminal Module 31 (TM31).
Digital output 1 of TM31 is a relay output.
If the signal at the binector input p4031 is low, then terminal COM 1 (X542.5) is connected to NC 1 (X542.4). This
connection also matches the mechanical quiescent setting of the relay.
If the signal at the binector input p4031 is high, then terminal COM 1 (X542.5) is connected to NO 1 (X542.6).
Note: DO: Digital Output
NC: Normally Closed contact
NO: Normally Open contact
p4032

BI: TM15DI/DO signal source for terminal DI/DO 2 / TM15D s_src DI/DO2

TM15DI_DO Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 2 (X520.4) of Terminal Module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.2 = 1).
DI/DO: Bidirectional Digital Input/Output
p4033

BI: TM15DI/DO signal source for terminal DI/DO 3 / TM15D s_src DI/DO3

TM15DI_DO Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 3 (X520.5) of Terminal Module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.3 = 1).
DI/DO: Bidirectional Digital Input/Output
p4034

BI: TM15DI/DO signal source for terminal DI/DO 4 / TM15D s_src DI/DO4

TM15DI_DO Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 4 (X520.6) of Terminal Module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.4 = 1).
DI/DO: Bidirectional Digital Input/Output
SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
2 Parameters
2.2 List of parameters
Access level: 1
Func. diagram: 9549, 9556
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9400
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9400
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9400
Unit selection: -
Expert list: 1
Factory setting
0
217