Bi: Tm15Di/Do Signal Source For Terminal Di/Do 13 / Tm15D S_Srcdi/Do13; Bi: Tm15Di/Do Signal Source For Terminal Di/Do 14 / Tm15D S_Srcdi/Do14; Tm31 Digital Outputs Limit Current / Tm31 Do Limit Curr - Siemens SINAMICS DCM List Manual

p4043

BI: TM15DI/DO signal source for terminal DI/DO 13 / TM15D s_srcDI/DO13

TM15DI_DO Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 13 (X521.7) of Terminal Module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.13 = 1).
DI/DO: Bidirectional Digital Input/Output
p4044

BI: TM15DI/DO signal source for terminal DI/DO 14 / TM15D s_srcDI/DO14

TM15DI_DO Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 14 (X521.8) of Terminal Module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.14 = 1).
DI/DO: Bidirectional Digital Input/Output
p4045 BI: TM15DI/DO signal source for terminal DI/DO 15 / TM15D s_srcDI/DO15
TM15DI_DO Can be changed: U, T
Data type: Unsigned32 / Binary
P-Group: Commands
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 15 (X521.9) of Terminal Module 15 (TM15).
Note: Prerequisite: The DI/DO must be set as an output (p4028.15 = 1).
DI/DO: Bidirectional Digital Input/Output
p4046

TM31 digital outputs limit current / TM31 DO limit curr

TM31 Can be changed: T
Data type: Integer16
P-Group: Commands
Not for motor type: -
Min
0
Description: Sets the limit for the total output voltage of terminals X541.1, X541.2, X541.3 and X541.4 (DI/DO 8 ... 11) of Terminal
Module 31 (TM31).
Value: 0:
1:
Dependency: Refer to: p4028
Warning: Since the sum of the output currents at terminals X541.1, X541.2, X541.3 and X541.4 is limited, an overcurrent or
short circuit at one output terminal can cause a dip in the signal at the other terminals.
SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
0.1 A total current limit DI/DO 8 ... 11
1.0 A total current limit DI/DO 8 ... 11
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
1
2 Parameters
2.2 List of parameters
Access level: 1
Func. diagram: 9401
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9401
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9401
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 2
Func. diagram: 9560
Unit selection: -
Expert list: 1
Factory setting
0
221