Siemens SINAMICS DCM List Manual page 29

43:
44:
45:
50:
51:
52:
53:
60:
61:
62:
63:
70:
71:
72:
73:
74:
75:
76:
77:
78:
79:
80:
81:
82:
83:
90:
91:
92:
93:
94:
95:
96:
97:
98:
99:
100:
101:
102:
103:
104:
105:
106:
107:
108:
109:
110:
120:
121:
122:
123:
124:
125:
126:
127:
128:
129:
Dependency: Refer to: r0046
Notice: For several missing enable signals, the corresponding value with the highest number is displayed.
Note: OC: Operating condition
RFG: Ramp-function generator
COMM: Commissioning
SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
o4.3 Operating state o4.3
o4.4 Operating state o4.4
o4.5 Wait until CCP pre-charged
o5.0 Wait for field current actual value
o5.1 Wait for voltage at 3U1, 3W1
o5.2 Operating state o5.2
o5.3 Operating state o5.3
o6.0 Wait until auxiliaries have been switched on
o6.1 Wait for small setpoint
o6.2 Operating state o6.2
o6.3 Operating state o6.3
o7.0 Wait for power-on via terminal 12
o7.1 Wait for power-on (signal source according to p0840)
o7.2 Stopping saved
o7.3 Wait for parallel master to power up
o7.4 Start of an optimization run
o7.5 Wait until SINAMICS DCM conn. in par. are rdy to switch on
o7.6 Operating state o7.6
o7.7 Operating state o7.7
o7.8 Operating state o7.8
o7.9 Operating state o7.9
o8.0 Switching on inhibited
o8.1 Simulation mode active
o8.2 Operating state o8.2
o8.3 Operating state o8.3
o9.0 Operating state o9.0
o9.1 Quick stop (OFF3) (signal source acc. to p0848) present
o9.2 Quick stop (OFF3) (signal source acc. to p0849) present
o9.3 Quick stop (OFF3) saved
o9.4 SS1 command (Safe Stop 1) present
o9.5 Operating state o9.5
o9.6 Operating state o9.6
o9.7 Operating state o9.7
o9.8 Operating state o9.8
o9.9 Operating state o9.9
o10.0 Operating state o10.0
o10.1 Voltage disconnect (OFF2) (signal source acc. to p0844)
o10.2 Voltage disconnect (OFF2) (signal source acc. to p0845)
o10.3 E stop (safety shutdown) (terminal 105/106)
o10.4 STO command (Safe Torque Off) present
o10.5 Operating state o10.5
o10.6 CUD right
o10.7 Operating state o10.7
o10.8 Operating state o10.8
o10.9 Operating state o10.9
o11.0 Fault present
o12.0 Initializ. of line voltage sensing for field in progress
o12.1 Initializ. of line voltage sensing for armature in progr.
o12.2 Operating state o12.2
o12.3 Reading out data of the gating modules
o12.4 Offset calibr. of curr. act. val. sensing being performed
o12.5 Read out data from the power unit
o12.6 Initializing the second processor (TMS320)
o12.7 Operating state o12.7
o12.8 Operating state o12.8
o12.9 Operating state o12.9
2 Parameters
2.2 List of parameters
29