Bi: Unconditionally Close Holding Brake / Uncond Close Brake; Co/Bo: Control Word Sequence Control / Stw Seq_Ctrl - Siemens SINAMICS DCM List Manual

2 Parameters
2.2 List of parameters
p0858[0...n]

BI: Unconditionally close holding brake / Uncond close brake

DC_CTRL, Can be changed: T
DC_CTRL_R,
Data type: Unsigned32 / Binary
DC_CTRL_R_S,
P-Group: Commands
DC_CTRL_S
Not for motor type: -
Min
-
Description: Sets the signal source for the command "unconditionally close holding brake".
Dependency: Refer to: p0855
Note: The signal via BI: p0858 (unconditionally close holding brake) has a higher priority than via BI: p0855 (unconditionally
open holding brake).
For a 1 signal via BI: p0858, the command "unconditionally close the holding brake" is executed and internally a zero
setpoint is entered.
r0898.0...14

CO/BO: Control word sequence control / STW seq_ctrl

DC_CTRL, Can be changed: -
DC_CTRL_R,
Data type: Unsigned16
DC_CTRL_R_S,
P-Group: Displays, signals
DC_CTRL_S
Not for motor type: -
Min
-
Description: Display and connector output for the control word of the sequence control.
Bit field: Bit
00
01
02
03
04
05
06
07
08
09
10
12
14
Note: OC: Operating condition
r0899.0...15 CO/BO: Status word sequence control / ZSW seq_ctrl
DC_CTRL, Can be changed: -
DC_CTRL_R,
Data type: Unsigned16
DC_CTRL_R_S,
DC_CTRL_S
P-Group: Displays, signals
Not for motor type: -
Min
-
Description: Displays the status word of the sequence control.
Bit field: Bit
00
01
02
03
04
05
06
07
104
Signal name
ON/OFF1
OC / OFF2
OC / OFF3
Operation enable
Ramp-function generator enable
Continue ramp-function generator
Speed setpoint enable
Command open brake
Jog 1
Jog 2
Master ctrl by PLC
Speed controller enable
Command close brake
Signal name
Rdy for switch on
Ready
Operation enabled
Jog active
No coasting active
No Quick Stop active
Switching on inhibited active
Drive ready
Calculated: -
Dyn. index: CDS, p0170
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
1 signal
Yes
Yes
Yes
Yes
OFF2 inactive
OFF3 inactive
Yes
Yes
List Manual (LH8), 02/2015, 6RX1800-0ED76
Access level: 2
Func. diagram: 2580
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 2
Func. diagram: 2580
Unit selection: -
Expert list: 1
Factory setting
-
0 signal
No
No
No
No
No
No
No
No
No
No
No
No
No
Access level: 2
Func. diagram: 2585, 2750,
3150, 3151, 3152, 6810, 6830
Unit selection: -
Expert list: 1
Factory setting
-
0 signal
No
No
No
No
OFF2 active
OFF3 active
No
No
SINAMICS DCM
FP
-
-
-
-
-
-
-
-
-
-
-
-
-
FP
-
-
-
-
-
-
-
-