Siemens SINAMICS DCM List Manual page 170

2 Parameters
2.2 List of parameters
p2116[0...n] BI: External alarm 2 / External alarm 2
DC_CTRL, Can be changed: U, T
DC_CTRL_R,
Data type: Unsigned32 / Binary
DC_CTRL_R_S,
P-Group: Messages
DC_CTRL_S
Not for motor type: -
Min
-
Description: Sets the signal source for external alarm 2.
Note: An external alarm is triggered with a 1/0 signal.
p2117 BI: External alarm 3 / External alarm 3
CU_DC, CU_DC_R, Can be changed: U, T
CU_DC_R_S,
Data type: Unsigned32 / Binary
CU_DC_S, TM150,
P-Group: Messages
TM15DI_DO, TM31
Not for motor type: -
Min
-
Description: Sets the signal source for external alarm 3.
Note: An external alarm is triggered with a 1/0 signal.
p2117[0...n] BI: External alarm 3 / External alarm 3
DC_CTRL, Can be changed: U, T
DC_CTRL_R,
Data type: Unsigned32 / Binary
DC_CTRL_R_S,
P-Group: Messages
DC_CTRL_S
Not for motor type: -
Min
-
Description: Sets the signal source for external alarm 3.
Note: An external alarm is triggered with a 1/0 signal.
p2118[0...19] Change message type message number / Chng type msg_no
CU_DC, CU_DC_R, Can be changed: U, T
CU_DC_R_S,
Data type: Unsigned16
CU_DC_S, TM150,
P-Group: Messages
TM15DI_DO, TM31
Not for motor type: -
Min
0
Description: Selects faults or alarms for which the message type should be changed.
Dependency: Selects the fault or alarm selection and sets the required type of message realized under the same index.
Refer to: p2119
Note: Re-parameterization is also possible if a message is present. The change only becomes effective after the message
has gone.
p2118[0...19] Change message type message number / Chng type msg_no
DC_CTRL, Can be changed: U, T
DC_CTRL_R,
Data type: Unsigned16
DC_CTRL_R_S,
P-Group: Messages
DC_CTRL_S
Not for motor type: -
Min
0
Description: Selects faults or alarms for which the message type should be changed.
170
Calculated: -
Dyn. index: CDS, p0170
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: CDS, p0170
Unit group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
65535
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
65535
List Manual (LH8), 02/2015, 6RX1800-0ED76
Access level: 3
Func. diagram: 2546
Unit selection: -
Expert list: 1
Factory setting
1
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
1
Access level: 3
Func. diagram: 2546
Unit selection: -
Expert list: 1
Factory setting
1
Access level: 3
Func. diagram: 8050, 8075
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 8075
Unit selection: -
Expert list: 1
Factory setting
0
SINAMICS DCM