Multi-Pump (Single Drive) Application Wizard - Danfoss VACON 100 FLOW Series Application Manual

VACON® 100 FLOW
Application Guide
12. Set a value for P3.13.1.4 Process Unit Selection.

If the selection is other than %, the next steps are shown. If the selection is %, the wizard goes directly to step 16.
13. Set a value for P3.13.1.5 Process Unit Min.
The range depends on the selection in step 12.
14. Set a value for P3.13.1.6 Process Unit Max.
The range depends on the selection in step 12.
15. Set a value for P3.13.1.7 Process Unit Decimals.
16. Set a value for P3.13.3.3 Feedback 1 Source Selection.
See the table Feedback settings in chapter

If analog input signal is selected, step 18 is shown. With other selections, the wizard goes to step 19.
17. Set the signal range of the analog input.
18. Set a value for P3.13.1.8 Error Inversion.
19. Set a value for P3.13.2.6 Setpoint Source Selection.
See table Setpoints in chapter

If analog input signal is selected, step 21 is shown. With other selections, the wizard goes to step 23. If Keypad
Setpoint 1 or Keypad Setpoint 2 are set for the value, the wizard goes directly to step 22.
20. Set the signal range of the analog input.
21. Set a value for P3.13.2.1 (Keypad Setpoint 1) and P3.13.2.2 (Keypad Setpoint 2).
Depends on the range set in step 20.
22. Using the sleep function.

If value Yes is set for step 22, the next 3 steps are shown. If the value No is selected, the wizard is completed.
23. Set a value for P3.13.5.1 SP1 Sleep Frequency Limit.
24.
Set a value for P3.13.5.2 SP1 Sleep Delay.
25. Set a value for P3.13.5.3 SP1 Wake-up Level.
The range depends on the set process unit.

The PID Control application wizard is completed.

4.1.4 Multi-pump (Single Drive) Application Wizard

The application wizard helps to set the basic parameters that are related to the application.
To start the Multi-pump (single drive application wizard, set the value PID Control to parameter P1.2 Application (ID 212) in the
keypad.
If the application wizard is started from the Start-up wizard, the wizard goes directly to step 11.
See the range of values of the parameters in
Brakes Setup, 6.13 Group 3.13: PID
Procedure
1. Set a value for P3.1.2.2 Motor Type (so that it agrees with the nameplate of the motor).

If Motor Type is set to Induction Motor, also step 6 is shown. If the selection is PM Motor, the value of parameter
P3.1.1.5 Motor Cos Phi is set to 1.00, and the wizard skips step 6.
2.
Set a value for P3.1.1.1 Motor Nominal Voltage (so that it agrees with the nameplate of the motor).
3. Set a value for P3.1.1.2 Motor Nominal Frequency (so that it agrees with the nameplate of the motor).
4.
Set a value for P3.1.1.3 Motor Nominal Speed (so that it agrees with the nameplate of the motor).
5. Set a value for P3.1.1.4 Motor Nominal Current (so that it agrees with the nameplate of the motor).
70 | Danfoss A/S © 2023.08
6.13 Group 3.13: PID
6.13 Group 3.13: PID Controller.
6.1 Group 3.1: Motor
Controller.
Controller.
Settings, 6.3 Group 3.3: References,
Wizards
6.4 Group 3.4: Ramps and
AB298035655957en-000201 / DPD01083