Mitsubishi Electric MELSEC iQ-R Series User Manual page 535

Name of variable Description
ends
 120
i = 1
ends
((endl + 20  en6)/1488)
en5
However, when endl is 0, en5 is 0.
When sf
sf = 1488-mod
i
However, the value is 0 when the calculation result of sf
en6 eRxln
However, when endl is 0, the value for en6 is 0.
endl eRxlAll
p1: RX/RY/RWr/RWw {((Total number of points of "RX setting") + (Total number of points of "RY setting"))/8 + ((Total number of points of "RWr
setting") + (Total number of points of "RWw setting"))  2}  5 + (Sn  3300)
processing time
However, if Total number of points of "RY setting" = Total number of points of "RX setting" = Total number of points of "RWr
setting" = Total number of points of "RWw setting" = 0, then p1 = 0.
p2: LB/LW processing time {((Total number of points of "LB setting" excluding master station)/8) + ((Total number of points of "LW setting" excluding
master station)  2) + ((Number of points of "LB setting" set in the master station)/8)  Ln + ((Number of points of "LW setting"
set in the master station)  2)  Ln}  5 + (Sn  6000)
However, if Total number of points of "LB setting" = Total number of points of "LW setting" = 0, then p2 = 0.
Sn  40
p3: Diagnostic information
processing time
kp 78000
1800  (Number of slave stations) + 10000
kuu: Inter-module
synchronization processing However, if the inter-module synchronization is not performed in the master station
time (unicast)
*1 The switching hub delay time changes depending on the hub models and settings.
*2 This is the slave station with the largest calculation value when, for each slave station (including extension modules), (("RX setting" +
"LB setting")/8) + (("RWr setting" + "LW setting")  2) is calculated.
*3 Calculate by rounding up each calculation result in brackets.
*4 In "Inter-module Synchronization Setting" under "System Parameter" of the master station, "Use Inter-module Synchronization Function
in System" is set to "Not Use" or "Select Inter-module Synchronization Target Module" is set to "Do Not Synchronize".
ends
i
 2
= eRxAll /8 + eRWrAll
i i i
i: Station number
eRxAll : 0 (fixed)
i
eRWrAll : Total number of points of "RWr setting" of extension modules with station No.i
i
*3
-k
i
20, k
>20, k = 1, and when sf
i i i i
mod: Remainder of {((mRx + (mRx /1468)
i i
i: Station number of the slave station
mRx : Number of points of "RX setting" of main modules with station No.i/8
i
: Number of points of "RWr setting" of main modules with station No.i  2
mRWr
i
+ eRWrln + ((endl+(eRxln + eRWrln
i i i
i: Station number of the slave station
eRxln : 0 (fixed)
i
eRWrln : Total number of extension modules with station No.i whose number of points of "RWr setting" is more than 0
i
 2
/8 + eRWrlAll
i i
i: Station number of the slave station
eRxlAll : 0 (fixed)
i
eRWrlAll : Total number of points of "RWr setting" of extension modules of the slave station
i
number of link points
= 0.
*3
 20) + (mRWr
+ (mRWr /1468)
i i
is 1488.
i
*2
to be used as the maximum number of link points
*3
)  20)/1488)
-1
i
*2
to be used as the maximum number of link points
*2
to be used as the maximum number of link points
Appendix 6 CC-Link IE TSN Processing Time
*3
 20))/1488}
*2
to be used as the maximum
*4
, then kuu = 0.
APPX
A
533