Mitsubishi Electric MELSEC iQ-R Series User Manual page 416

Error Error definition and causes
code
3604H A module to operate as an inter-module
synchronous master could not output an
inter-module synchronization signal.
3605H A module to operate as an inter-module
synchronous master could not output an
inter-module synchronization signal.
3607H The correction value of time counter
calculated by the inter-module
synchronization function exceeds
allowable range successively.
3608H Inter-module synchronization signals have
not been input for a certain period of time.
3609H An error has been detected in the inter-
module synchronization function.
360AH An error has been detected in the inter-
module synchronization function.
360BH An error has been detected in the inter-
module synchronization function.
360CH An error has been detected in the inter-
module synchronization function.
3C00H A hardware failure has been detected.
3C01H A hardware failure has been detected.
19 LIST OF ERROR CODES
414
19.1 Error Codes When a Module Error Occurs
Action
• Check if the switching hub and the cables are connected properly.
• Power off and on or reset the own station.
• When an error with this error code is detected in multiple RJ71GN11-T2s
(local stations) and/or RJ71GN11-EIPs (local stations), power off and on
or reset the RJ71GN11-T2s (local stations) and/or RJ71GN11-EIPs (local
stations) in order of connection nearest to the master station.
• Check the master station condition.
• Check the error of the master station and take action using the module
diagnostics of the engineering tool.
• Check that the settings of the master station are consistent with the one of
the slave station in "Network Configuration Settings" under "Basic
Settings" of the master station.
• Check that the settings of the master station are consistent with the one of
the local station in "IP Address" under "Required Settings" of the local
station.
• Correct the "IP Filter Settings" under "Application Settings".
• Check if the switching hub and the cables are connected properly.
• Power off and on or reset the own station.
• When an error with this error code is detected in multiple RJ71GN11-T2s
(local stations) and/or RJ71GN11-EIPs (local stations), power off and on
or reset the RJ71GN11-T2s (local stations) and/or RJ71GN11-EIPs (local
stations) in order of connection nearest to the master station.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module or base unit. Please consult your local Mitsubishi
representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module or base unit. Please consult your local Mitsubishi
representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module or base unit. Please consult your local Mitsubishi
representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module or base unit. Please consult your local Mitsubishi
representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module or base unit. Please consult your local Mitsubishi
representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module or base unit. Please consult your local Mitsubishi
representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module, base unit, or extension cable. Please consult your local
Mitsubishi representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error occurs again
even after taking the above, the possible cause is a hardware failure of
the module, base unit, or extension cable. Please consult your local
Mitsubishi representative.
Detailed
information 1
Detailed
information 2
■
■Synchronous
master setting
information
• Synchronous
master mounted
slot number
■
■Synchronous
master setting
information
• Synchronous
master mounted
slot number







