Mitsubishi Electric MELSEC iQ-R Series User Manual page 439

Stored Stored Stored
value in (1) value in (3) value in (4)
or (2) or (5) or (6)

41H (scanner) 10H
51H (adapter)

41H (scanner) 13H
51H (adapter)

41H (scanner) 15H
51H (adapter)
41H (scanner) Except for 
51H (adapter) shown above
43H (scanner) 00H 0002H
43H (scanner) 00H 02BCH
43H (scanner) 00H 012EH
43H (scanner) 00H 012FH
43H (scanner) 00H 0130H
43H (scanner) 00H 01C3H
44H (scanner) 00H 0002H
Classification Error definition and
causes
CIP Extended An error notification has
error been received from the
external device.
CIP Extended An error notification has
error been received from the
external device.
CIP Extended An error notification has
error been received from the
external device.
CIP Extended An error notification has
error been received from the
external device.
Connection start Network path error
error
Connection start Memory error
error
Connection start Specified connection
error instance ID duplication
Connection start Invalid target IP address
error
Connection start No TCP/IP interface
error object for the specified IP
address
Connection start EtherNet/IP
error configuration parameter
error
Connection error The target device does
not exist.
Action
Refer to the manuals for the external device and the
EtherNet/IP specification (THE CIP NETWORKS LIBRARY
Volume 1 Common Industrial Protocol (CIP
conditions under which a notification is made for this error
and the action to take.
Refer to the manuals for the external device and the
EtherNet/IP specification (THE CIP NETWORKS LIBRARY
Volume 1 Common Industrial Protocol (CIP
conditions under which a notification is made for this error
and the action to take.
Refer to the manuals for the external device and the
EtherNet/IP specification (THE CIP NETWORKS LIBRARY
Volume 1 Common Industrial Protocol (CIP
conditions under which a notification is made for this error
and the action to take.
Refer to the manuals for the external device and the
EtherNet/IP specification (THE CIP NETWORKS LIBRARY
Volume 1 Common Industrial Protocol (CIP
conditions under which a notification is made for this error
and the action to take.
• Stored value in (3) or (5): Value of General Status notified
by the external device
• Stored value in (4) or (6): Value of Extended Status notified
by the external device
• Check the parameter set in "EtherNet/IP Configuration"
and write the parameter to the module again.
• If the same error code is displayed again, the possible
cause is a hardware failure of the error module. Please
consult your local Mitsubishi representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error
occurs again even after taking the above measure, the
possible cause is a hardware failure of the module. Please
consult your local Mitsubishi representative.
• Take measures to reduce noise.
• Reset the CPU module, and run it again. If the same error
occurs again even after taking the above measure, the
possible cause is a hardware failure of the module. Please
consult your local Mitsubishi representative.
• Check the parameter set in "EtherNet/IP Configuration"
and write the parameter to the module again.
• If the same error code is displayed again, the possible
cause is a hardware failure of the error module. Please
consult your local Mitsubishi representative.
• Check the parameter set in "EtherNet/IP Configuration"
and write the parameter to the module again.
• If the same error code is displayed again, the possible
cause is a hardware failure of the error module. Please
consult your local Mitsubishi representative.
• Check the parameter set in "EtherNet/IP Configuration"
and write the parameter to the module again.
• If the same error code is displayed again, the possible
cause is a hardware failure of the error module. Please
consult your local Mitsubishi representative.
• Check whether the operating status of the external device
is normal.
• Check for errors in the line status.
• The line may be busy, so retry the operation after a while.
• The external device may not be able to transmit data at the
specified RPI due to a high communication load, so
specify a larger RPI and connect again.
19 LIST OF ERROR CODES
19.3 Error Codes When a Connection Error Occurs

)) to check the

19
)) to check the

)) to check the

)) to check the
437