Huawei SmartAX MA5616 Configuration Manual page 527

SmartAX MA5616 Multi-service Access Module
Configuration Guide
Issue 04 (2011-10-30)
– If the ONU fails to be in the up state, that is, Run state is offline, the physical line
may be broken or the optical transceiver may be damaged. You need to check both
the material and the line.
– If the ONU state fails, that is, Config state is failed, the ONU capability set
outmatches the actual ONU capabilities. In this case, run the display ont failed-
configuration command in the diagnosis mode to check the failed configuration
item and the failure cause. Then, rectify the fault according to actual conditions.
NOTE
If an ONT supports only four queues, the values of 4-7 of the priority-queue parameter in the
gem add command are invalid. After configuration recovers, Config state will be failed.
6. Configure the management channel from the OLT to the ONU.
a. Configure the inband management VLAN and IP address of the OLT.
To telnet to the ONU from the OLT and then configure the ONU, you need to
configure the inband management VLANs and IP addresses of the OLT and the
ONU on the OLT.
Create management VLAN 8, and configure the inband management IP address
to 192.168.50.1/24.
huawei(config)#vlan 8 smart
huawei(config)#interface vlanif 8
huawei(config-if-vlanif8)#ip address 192.168.50.1 24
huawei(config-if-vlanif8)#quit
b. Configure the inband management VLAN and IP address of the ONU.
Configure the static IP address of the ONU 1 to 192.168.50.2/24, the static IP
address of the ONU 2 to 192.168.50.3/24 , the gateway to 192.168.50.254 and
the management VLAN ID to 8 (the same as that of the OLT) .
huawei(config-if-gpon-0/2)#ont ipconfig 1 1 static ip-address
192.168.50.2
mask 255.255.255.0 gateway 192.168.50.254 vlan 8
huawei(config-if-gpon-0/2)#ont ipconfig 1 2 static ip-address
192.168.50.3
mask 255.255.255.0 gateway 192.168.50.254 vlan 8
huawei(config-if-gpon-0/2)#quit
c. Configure an inband management service port.
Configure the management service port index to 0, management VLAN ID to 8,
GEM port ID to 0, and CVLAN ID to 8. On the OLT, the rate of the inband
service port is not limited. Therefore, use default traffic profile 6. To limit the
rate of a service port, run the traffic table ip command to create a traffic profile
and then bind the profile to the service port.
huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
huawei(config)#service-port 2 vlan 8 gpon 0/2/1 ont 2 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
7. Confirm that the management channel between the OLT and the ONU is available.
– On the OLT, run the ping 192.168.50.2 and ping 192.168.50.3 command to check
the connectivity to the ONU 1 and ONU 2. The ICMP ECHO-REPLY packet from
the ONU should be received.
– You can run the telnet 192.168.50.2 and telnet 192.168.50.3 command to telnet
to the ONU 1 and ONU 2 and then configure the ONU.
8. Configure the traffic profile.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10 Configuration Examples of the FTTx
516