Huawei SmartAX MA5616 Configuration Manual page 546

SmartAX MA5616 Multi-service Access Module
Configuration Guide
Issue 04 (2011-10-30)
service port is not limited. Therefore, use default traffic profile 6. To limit the
rate of a service port, run the traffic table ip command to create a traffic profile
and then bind the profile to the service port.
huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
huawei(config)#service-port 2 vlan 8 gpon 0/2/1 ont 2 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
7. Confirm that the management channel between the OLT and the ONU is available.
– On the OLT, run the ping 192.168.50.2 and ping 192.168.50.3 command to check
the connectivity to the ONU 1 and ONU 2. The ICMP ECHO-REPLY packet from
the ONU should be received.
– You can run the telnet 192.168.50.2 and telnet 192.168.50.3 command to telnet
to the ONU 1 and ONU 2 and then configure the ONU.
8. Create a service port.
Create service port 1000 connected to ONU 1 and service port 1001 connected to ONU
2. SVLAN ID to 1000, GEM port ID to 1, and CVLAN ID to 1001. Rate limitation
for upstream and downstream packets is performed on the ONU instead of on the OLT.
Therefore, use traffic profile 6 (default). To limit the rate of the service port, run the
traffic table ip command to add a traffic profile and bind it to the service port.
NOTE
The CVLAN must be consistent with the upstream VLAN of the ONU.
huawei(config)#service-port 1000 vlan 1000 gpon 0/2/1 ont 1 gemport 1
multi-service user-vlan 1000 rx-cttr 6 tx-cttr 6
huawei(config)#service-port 1001 vlan 1000 gpon 0/2/1 ont 2 gemport 1
multi-service user-vlan 1000 rx-cttr 6 tx-cttr 6
9. Configure the queue scheduling mode.
Adopt the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode and their
weights are 10, 10, 20, 20, and 40 respectively. Queues 5-7 adopt the PQ mode. The
priority of the IPTV service is 4, adopting the WRR mode.
NOTE
l The queue scheduling mode is configured globally, and you need to configure it only once on
the OLT. After the configuration is complete, the queue scheduling mode takes effect globally.
When subsequent services are configured, you do not need to configure the queue scheduling
mode again.
l For a board that supports only four queues, the mapping between the 802.1p priorities and queue
IDs are as follows: priorities 0 and 1 map queue 1; priorities 2 and 3 map queue 2; priorities 4
and 5 map queue 3; priorities 6 and 7 map queue 4.
huawei(config)#queue-scheduler wrr 10 10 20 20 40 0 0 0
Configure the mapping between the queues and 802.1p priorities. Priorities 0-7 map
queues 0-7 respectively.
huawei(config)#cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6
6 cos7 7
10. Configure a multicast subtending port.
Configure port 0/2/1 connected to the ONU as a multicast subtending port.
huawei(config)#btv
huawei(config-btv)#igmp cascade-port 0/2/1 ontid 1 gemport 1
huawei(config-btv)#igmp cascade-port 0/2/1 ontid 2 gemport 1
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10 Configuration Examples of the FTTx
535