Huawei SmartAX MA5616 Configuration Manual page 344

SmartAX MA5616 Multi-service Access Module
Configuration Guide
4.
5.
Step 6 Configure the PPPoA-PPPoE protocol conversion.
This step is to configure the PPPoA MAC address pool. The start MAC address in the MAC
address pool is 0000-1111-1010, and the maximum number of the MAC addresses in the MAC
address pool is 300. The PPPoA-PPPoE protocol conversion is enabled and the service
encapsulation mode is LLC.
huawei(config)#mac-pool xpoa 0000-1111-1010 300
huawei(config)#pppoa enable
huawei(config)#encapsulation 0/2/0 vpi 1 vci 39 type pppoa llc
huawei(config)#encapsulation 0/4/0 vpi 1 vci 39 type pppoa llc
huawei(config)#encapsulation 0/1/0 vpi 1 vci 39 type pppoa llc
Step 7 Configure the user account security.
The PITP P mode can be enabled to protect the user account against theft and roaming. The
RAIO mode can be customized according to actual requirements. Here, the cntel is considered
as an example.
huawei(config)#pitp enable pmode
huawei(config)#raio-mode cntel pitp-pmode
Issue 04 (2011-10-30)
pri
1 2496
pri
2 512
pri
3 576
pri
4 64
pri
5 2048
pri
6 off
pri
----------------------------------------------------------------------------
Total Num : 7
According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.
NOTE
l If no traffic profile in the system meets the service requirement, run the traffic table ip command to
configure a new traffic profile.
l On the MA5616, the user access rate can be limited by either a traffic profile or a VDSL line profile.
When both profiles are configured, the user bandwidth adopts the minimum value in the two profiles.
In this example, the traffic profile is used to limit the user access rate.
Run the service-port command to create a service port. The index of the new service virtual
port is 3, the access port is port 0/1/0, traffic profile 5 meets the service requirement, and
the S-VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and
VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1
and 39. To facilitate the maintenance of the service port, also configure the service port
description.
huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39
traffic-table index 5 outbound
traffic-table index 5
huawei(config)#service-port desc 3 description MA5616HW/Vlanid:50/vdsl/smart
Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.
huawei(config)#mac-address max-mac-count service-port 3 16
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8 Configuration Example of Services on the MA5616
81872 4992 163744
18384 1024
20432 1152
4048 128
67536 4096 135072
off off
Through GPON Upstream Transmission
6 -
36768 0 -
40864 2 -
8096 4 -
0 -
off 0 -
tag-
tag-
tag-
tag-
tag-
tag-
inbound
333