Huawei SmartAX MA5616 Configuration Manual page 518

SmartAX MA5616 Multi-service Access Module
Configuration Guide
Issue 04 (2011-10-30)
huawei(config)#vlan 8 smart
huawei(config)#interface vlanif 8
huawei(config-if-vlanif8)#ip address 192.168.50.1 24
huawei(config-if-vlanif8)#quit
b. Configure the inband management VLAN and IP address of the ONU.
Configure the static IP address of the ONU 1 to 192.168.50.2/24, the static IP
address of the ONU 2 to 192.168.50.3/24 , the gateway to 192.168.50.254 and
the management VLAN ID to 8 (the same as that of the OLT) .
huawei(config-if-gpon-0/2)#ont ipconfig 1 1 static ip-address
192.168.50.2
mask 255.255.255.0 gateway 192.168.50.254 vlan 8
huawei(config-if-gpon-0/2)#ont ipconfig 1 2 static ip-address
192.168.50.3
mask 255.255.255.0 gateway 192.168.50.254 vlan 8
huawei(config-if-gpon-0/2)#quit
c. Configure an inband management service port.
Configure the management service port index to 0, management VLAN ID to 8,
GEM port ID to 0, and CVLAN ID to 8. On the OLT, the rate of the inband
service port is not limited. Therefore, use default traffic profile 6. To limit the
rate of a service port, run the traffic table ip command to create a traffic profile
and then bind the profile to the service port.
huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
huawei(config)#service-port 2 vlan 8 gpon 0/2/1 ont 2 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
7. Confirm that the management channel between the OLT and the ONU is available.
– On the OLT, run the ping 192.168.50.2 and ping 192.168.50.3 command to check
the connectivity to the ONU 1 and ONU 2. The ICMP ECHO-REPLY packet from
the ONU should be received.
– You can run the telnet 192.168.50.2 and telnet 192.168.50.3 command to telnet
to the ONU 1 and ONU 2 and then configure the ONU.
8. Create service ports.
Create service port 101 connected to ONU 1 and service port 102 connected to ONU
2. Set the SVLAN ID to 100, GEM port ID to 1, and CVLAN ID to 1001. The traffic
rate of upstream and downstream packets is limited on the ONU and not limited on
the OLT. Therefore, use default traffic profile 6. To limit the rate of a service port,
run the traffic table ip command to create a traffic profile and then bind the profile
to the service port.
Assume the split ratio is 1:128. ONU 1 is connected to port 1 on the optical splitter
by using optical fiber and ONU 2 is connected to port 2. The user PC is connected to
ONU port 1. The inner VLAN IDs are 258 and 260 after they are calculated according
to the formula.
huawei(config)#service-port 101 vlan 100 gpon 0/2/1 ont 1 gemport 1 multi-
service
user-vlan 1001 tag-transform translate-and-add inner-vlan 258 rx-cttr 6 tx-
cttr 6
huawei(config)#service-port 102 vlan 100 gpon 0/2/1 ont 2 gemport 1 multi-
service
user-vlan 1001 tag-transform translate-and-add inner-vlan 260 rx-cttr 6 tx-
cttr 6
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10 Configuration Examples of the FTTx
507