Huawei SmartAX MA5616 Configuration Manual page 509

SmartAX MA5616 Multi-service Access Module
Configuration Guide
Issue 04 (2011-10-30)
mask 255.255.255.0 gateway 192.168.50.254 vlan 8
huawei(config-if-gpon-0/2)#quit
c. Configure an inband management service port.
Configure the management service port index to 0, management VLAN ID to 8,
GEM port ID to 0, and CVLAN ID to 8. On the OLT, the rate of the inband
service port is not limited. Therefore, use default traffic profile 6. To limit the
rate of a service port, run the traffic table ip command to create a traffic profile
and then bind the profile to the service port.
huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
huawei(config)#service-port 2 vlan 8 gpon 0/2/1 ont 2 gemport 0 multi-
service
user-vlan 8 rx-cttr 6 tx-cttr 6
7. Confirm that the management channel between the OLT and the ONU is available.
– On the OLT, run the ping 192.168.50.2 and ping 192.168.50.3 command to check
the connectivity to the ONU 1 and ONU 2. The ICMP ECHO-REPLY packet from
the ONU should be received.
– You can run the telnet 192.168.50.2 and telnet 192.168.50.3 command to telnet
to the ONU 1 and ONU 2 and then configure the ONU.
8. Create service ports.
Create service port 101 connected to ONU 1 and service port 102 connected to ONU
2. Set the SVLAN ID to 100, GEM port ID to 1, and CVLAN ID to 1001. The traffic
rate of upstream and downstream packets is limited on the ONU and not limited on
the OLT. Therefore, use default traffic profile 6. To limit the rate of a service port,
run the traffic table ip command to create a traffic profile and then bind the profile
to the service port.
Assume the split ratio is 1:128. ONU 1 is connected to port 1 on the optical splitter
by using optical fiber and ONU 2 is connected to port 2. The user PC is connected to
ONU port 1. The inner VLAN IDs are 258 and 260 after they are calculated according
to the formula.
huawei(config)#service-port 101 vlan 100 gpon 0/2/1 ont 1 gemport 1 multi-
service
user-vlan 1001 tag-transform translate-and-add inner-vlan 258 rx-cttr 6 tx-
cttr 6
huawei(config)#service-port 102 vlan 100 gpon 0/2/1 ont 2 gemport 1 multi-
service
user-vlan 1001 tag-transform translate-and-add inner-vlan 260 rx-cttr 6 tx-
cttr 6
NOTE
l The OLT's CVLAN must be the same as the upstream VLAN of the ONU.
l Run the service-port to create service ports one by one. In this example, only one service port
is created as an example. When a service port is created, note that it must correspond to the GEM
port configured with the ONU line-profile and the CVLAN.
l You can also run the multi-service-port command to create service ports in batches. In the case
of GPON access, you must set ontid+gemindex to specify a service port. In addition, the number
of GEM ports must be the same as the number of CVLANs.
9. Configure the queue scheduling mode.
Adopt the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode and their
weights are 10, 10, 20, 20, and 40 respectively. Queues 5-7 adopt the PQ mode. The
priority of the Internet access service is 1, adopting the WRR mode.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10 Configuration Examples of the FTTx
498