Huawei SmartAX MA5616 Configuration Manual page 410

SmartAX MA5616 Multi-service Access Module
Configuration Guide
Procedure
Step 1 Configure a VLAN.
Configure S-VLAN 50 with the stacking attribute. The user packet goes upstream carrying two
VLAN tags. The outer VLAN tag identifies the service and the inner VLAN tag identifies the
user. The service of each user is identified by unique S-VLAN+C-VLAN, and the VLAN
forwarding mode is the S-VLAN+C-VLAN mode.
huawei(config)#vlan 50 smart
huawei(config)#vlan attrib 50 stacking
huawei(config)#vlan service-profile profile-id 1
huawei(config-vlan-srvprof-1)#forwarding vlan-connect
huawei(config-vlan-srvprof-1)#commit
huawei(config-vlan-srvprof-1)#quit
huawei(config)#vlan bind service-profile 50 profile-id 1
Step 2 Configure upstream ports.
Add upstream ports 0/0/1 and 0/0/0 to VLAN 50. Two ports are added for the purpose of port
aggregation.
huawei(config)#port vlan 50 0/0 0
huawei(config)#port vlan 50 0/0 1
To aggregate the two upstream ports as one aggregation group, set the packet forwarding mode
of the aggregation group to egress-ingress, and set the aggregation group to work in the LACP
static mode, do as follows:
huawei(config)#link-aggregation 0/0 0 0/0 1 egress-ingress workmode lacp-static
The aggregated ports must meet the following requirements: The ports must work in the full-duplex mode; the
port rates must be the same and the rate of an electrical port must not be of the auto-negotiation type; the attributes
of the ports, such as the default VLAN ID (PVID) and VLAN, must be the same; one port can belong to only
one aggregation group; the port must not be a mirroring destination port; the port must not be in the auto-
negotiation mode; the start port ID must be smaller than the end port ID.
Step 3 In the ADSL access mode, follow this procedure.
1.
2.
3.
Issue 04 (2011-10-30)
MA5616 in the upstream direction. For the identification purpose, the user name and
password for dial-up Internet access must be configured on the BRAS.
NOTE
Configure an ADSL2+ profile. For details, see
Here, the default ADSL2+ line template (line template 1) and the default ADSL2+ alarm
template (alarm template 1) are used as an example.
Activate the ADSL port, and bind the ADSL2+ templates.
NOTE
By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.
In the ADSL access mode, bind the default ADSL2+ line template 1 and ADSL2+ alarm
template 1 to ADSL port 0/2/0.
huawei(config)#interface adsl 0/2
huawei(config-if-adsl-0/2)#deactivate 0
huawei(config-if-adsl-0/2)#activate 0 template-index 1
huawei(config-if-adsl-0/2)#alarm-config 0 1
huawei(config-if-adsl-0/2)#quit
Run the display traffic table command to query the existing traffic profiles in the system.
huawei(config)#display traffic table ip from-index
0
{ <cr>|to-
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9 Configuration Example of Services on the MA5616
Through GE Upstream Transmission
3.7.1 Configuring the ADSL2+ Profile.
399