Huawei SmartAX MA5616 Configuration Manual page 515

SmartAX MA5616 Multi-service Access Module
Configuration Guide
Issue 04 (2011-10-30)
Create GPON ONU line profile 10 and bind T-CONT 4 to DBA profile PPPoE.
In this way, the T-CONT can provide flexible DBA solutions based on different
configurations in the DBA profile.
huawei(config)#ont-lineprofile gpon profile-id 10
huawei(config-gpon-lineprofile-10)#tcont 4 dba-profile-name PPPoE
NOTE
The ID of the line profile to be created must not exist in the system. Please create proper ONU
line profiles according to actual data plan. In this example, line profile 10 is used.
Add GEM port 0 for transmitting management traffic streams and GEM port 1
for transmitting Internet traffic streams. Bind GEM port 0 and GEM port 1 to T-
CONT 4. Set the QoS mode to priority-queue (default).
huawei(config-gpon-lineprofile-10)#gem add 0 eth tcont 4
huawei(config-gpon-lineprofile-10)#gem add 1 eth tcont 4
NOTE
a. To change the QoS mode, run the qos-mode command to configure the QoS mode to gem-
car or flow-car, and run the gem add command to configure the ID of the traffic profile
bound to the GEM port.
b. For the ONU V800R308, the QoS mode cannot be set to gem-car or flow-car. To
implement QoS in the upstream and downstream directions, other modes are adopted. For
example, bind a T-CONT to a DBA profile or bind a traffic profile when creating traffic
streams.
c. When the QoS mode is PQ, the default queue priority is 0; when the QoS is gem-car or
flow-car, traffic profile 6 is bound to the port by default (no rate limitation).
d. Before running the multi-service-port command to create service ports in batches, ensure
that the number of GEM ports is the same as the number of CVLANs. Therefore, you must
create GEM ports according to the number of CVLANs. If there are 24 CVLANs,, 24
GEM ports need to be created.
e. If you run the service-port command to create service ports one by one, note that one
GEM port can be bound to up to eight service ports. Create sufficient GEM ports according
to the number of service ports. If there are 24 CVLANs, at least three GEM ports need to
be created. This example adopts this mode and only one GEM port is created. For different
service ports within the same GEM port, you only need to replace the mapping-index and
replace the mapped VLAN with the CVLAN.
Configure the mapping between the GEM port and the ONU-side service to the
VLAN mapping mode (default), map the service port of management service
port ( the CVLAN ID is 8) to GEM port 0, and map the Internet service port (the
CVLAN ID is 1001) to GEM port 1.
huawei(config-gpon-lineprofile-10)#mapping-mode vlan
huawei(config-gpon-lineprofile-10)#gem mapping 0 0 vlan 8
huawei(config-gpon-lineprofile-10)#gem mapping 1 1 vlan 1001
After the configuration is complete, run the commit command to make the
configured parameters take effect.
huawei(config-gpon-lineprofile-10)#commit
huawei(config-gpon-lineprofile-10)#quit
c. (Optional) Configure an alarm profile.
– The ID of the default GPON alarm profile is 1. The thresholds of all the alarm
parameters in the default alarm profile are 0, which indicates that no alarm is
generated.
– In this example, the default alarm profile is used, and therefore the
configuration of the alarm profile is not required.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10 Configuration Examples of the FTTx
504