Huawei SmartAX MA5616 Configuration Manual page 348

SmartAX MA5616 Multi-service Access Module
Configuration Guide
4.
5.
Step 4 In the case of the SHDSL access mode, follow this procedure.
1.
2.
3.
Issue 04 (2011-10-30)
2 512
pri
3 576
pri
4 64
pri
5 2048
pri
6 off
pri
----------------------------------------------------------------------------
Total Num : 7
According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.
NOTE
l If no traffic profile in the system meets the service requirement, run the traffic table ip command to
configure a new traffic profile.
l On the MA5616, the user access rate can be limited by either a traffic profile or an ADSL line profile.
When both profiles are configured, the user bandwidth adopts the minimum value in the two profiles.
In this example, the traffic profile is used to limit the user access rate.
Run the service-port command to create a service port. The index of the new service port
is 1, the access port is port 0/2/0, traffic profile 5 meets the service requirement, and the S-
VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and VCI
of the peer modem. Assume that the management VPI and VCI of the modem are 1 and
39. To facilitate the maintenance of the service port, also configure the service port
description.
huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic-
table index 5 outbound traffic-table index 5
huawei(config)#service-port desc 1 description MA5616HW/Vlanid:50/adsl/smart
Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.
huawei(config)#mac-address max-mac-count service-port 1 16
Configure an SHDSL profile. For details, see
ID of the SHDSL line profile is 3, the line rate is 2048 kbit/s, and the profile is used to
activate 4-wire ports.
huawei(config)#shdsl line-profile quickadd 3 line four-wire rate 2048
Activate the SHDSL port. The port is port 0/4/0, and SHDSL line profile 3 and the default
alarm profile (alarm profile 1) are bound to the port.
NOTE
By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.
huawei(config)#interface shl 0/4
huawei(config-if-shl-0/4)#deactivate 0
huawei(config-if-shl-0/4)#activate 0 3
huawei(config-if-shl-0/4)#alarm-config 0 1
huawei(config-if-shl-0/4)#quit
Run the display traffic table ip command to query the traffic profiles that exist in the
system.
huawei(config)#display traffic table ip from-index
0
{ <cr>|to-
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8 Configuration Example of Services on the MA5616
18384 1024
20432 1152
4048 128
67536 4096 135072
off off
3.7.2 Configuring the SHDSL
Through GPON Upstream Transmission
36768 0 -
40864 2 -
8096 4 -
0 -
off 0 -
tag-
tag-
tag-
tag-
tag-
Profile. The
337