Dc131 Nvm Read/Write - Xerox Phaser 3635MFP Service Manual

dC131 NVM Read/Write

Purpose
To review and modify values within the machine configuration and control parameters stored in
NVM.
Description
Each NVM item is identified using a chain and location code in the form XX-XXX, where XX- is
the chain prefix, and -XXX is an identifier in the range 001 to 999. For example 05-100.
Procedure
Refer to the relevant procedure:
• 3635 NVM Read/Write
• 3550 NVM Read/Write
3635 NVM Read/Write
1. Enter diagnostics, GP 1 Diagnostics
2. Select Diagnostic Routines.
3. Select the required dC routine category:
• Copier Routines.
• Fax dC Routines.
4. Select 131 NVM Read/Write.
5. Select the appropriate button for the NVM chain to be viewed.
6. Use the scroll buttons to view the other NVM locations of the chain.
• Use the keyboard to type the three digit identifier code into the Find: field and then
touch the Find: button. This puts the found NVM value at the top of the list.
NOTE: Press the keypad C button to reset the Find: button to 000.
7. Touch the selected NVM in the list, and touch the Read/Write button.
• The Read/Write window will open for editable NVM, and the Read Only window will
open for Read Only (protected) NVM.
8. Refer to the tables that follow for NVM chain locations and parameters:
• Table 1 NVM chain 6
• Table 2 NVM chain 7
• Table 3 NVM chain 9
• Table 4 NVM chain 10
• Table 5 NVM chain 20
9. When the values of an editable NVM have been changed, switch off the machine, then
switch on the machine, to check and evaluate the changes made to the NVM.
NOTE: If the NVM default characters exceed 10 characters only the first eight characters are
displayed in the list. The full string is displayed in the Read/Write window.
NOTE: Selecting Reset will cause the selected NVM location to be reset to its default value.
Selecting Cancel closes the window and cancels any changes made in the now closed win-
dow.
NOTE: The CSE cannot read or modify any NVM that contains customer administrative or
accounting data.
Phaser 3635MFP/WorkCentre 3550
Entry.
NOTE: The Read Only (protected) NVM can only be changed using a password obtained from
Xerox.
Location NVM Name NVM Description
06-100 Vertical Magni- The changed dimension of the
tude vertical direction magnitude.
06-110 Horizontal Magni- The changed dimension of the
tude horizontal direction magnitude.
Location NVM Name NVM Description
07-100 Top Registration The changed dimension of tray
Tray 1 Simplex 1 top registration in simplex.
07-110 Side Registration The changed dimension of tray
Tray 1 Simplex 1 side registration in simplex.
07-120 Top Registration The changed dimension of tray
Tray 1 Dup_long 1 top registration of 2nd side in
(2nd sid)e duplex long.
07-130 Side Registration The changed dimension of tray
Tray 1 Dup_long 1 side registration of 2nd side
(2nd sid)e in duplex long.
07-140 Top Registration The changed dimension of tray
Tray 1 Duplex 1 top registration of 1st side in
(1st sid)e duplex long and short.
07-150 Side Registration The changed dimension of tray
Tray 1 Duplex 1 side registration of 1st side in
(1st sid)e duplex long and short.
07-200 Top Registration The changed dimension of tray
Tray 2 Simplex 2 top registration in simplex.
07-210 Side Registration The changed dimension of tray
Tray 2 Simplex 2 side registration in simplex.
07-220 Top Registration The changed dimension of tray
Tray 2 Dup_long 2 top registration of 2nd side in
(2nd sid)e duplex long.
07-230 Side Registration The changed dimension of tray
Tray 2 Dup_long 2 side registration of 2nd side
(2nd sid)e in duplex long.
07-240 Top Registration The changed dimension of tray
Tray 2 Duplex 2 top registration of 1st side in
(1st sid)e duplex long and short.
April 2010
6-35
Table 1 NVM chain 6
Value
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
Table 2 NVM chain 7
Value
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
0mm to 6mm
(13 steps /
0.5mm seg.)
General Procedures/Information
Default
3
3
Default
3
3
3
3
3
3
3
3
3
3
3
dC131