Table of Contents
Advertisement
D
E
Go to
Flag 10
on BSD 12.12. Check for an open circuit or a short circuit to GND. If the
wires are good, replace the Stapler Position Motor
replace the Finisher PWB
(PL
18.4).
Ensure that the Stapler is in the front position and that the Stapler Front Corner Sensor is
blocked (manually move the Stapler toward the front if necessary). Enter dC330 012-269 Sta-
pler Front Corner Sensor. Press Start. The display indicates High.
Y
N
Go to
Flag 7
on BSD 12.12. Check the wire for a short circuit to GND. If the wire is good,
replace the Stapler Front Corner Sensor
Finisher PWB
(PL
18.4).
Move the Stapler to the rear, to unblock the Stapler Front Corner Sensor. The
changes to Low.
Y
N
Disconnect
P/J1057
from the Stapler Front Corner Sensor. +5
between J1057-1 and J1057-3.
Y
N
Go to
Flag 6
on BSD 12.12. Check the wires for an open circuit or a short circuit to
GND. If the wires are good, replace the Finisher PWB
Go to
Flag 7
on BSD 12.12. Check the wire for an open circuit. If the wire is good, replace
the Stapler Front Corner Sensor
(PL
PWB.
Perform the following:
•
Manually move the Stapler toward the front and rear of the Finisher to ensure that it
moves smoothly and that there are no obstructions in the Stapler travel. Correct any prob-
lems found.
•
Replace the Stapler Front Corner Sensor
•
If the problem continues, replace the Finisher PWB
Reissue
DocuColor 12/DCCS50
(PL
18.17). If the problem continues,
(PL
18.18). If the problem continues, replace the
VDC
is
(PL
18.4).
18.18). If the problem continues, replace the Finisher
(PL
18.18).
(PL
18.4).
12-246 RAP
This fault is caused by one of the following conditions:
•
During Initialization, the Control Logic does not detect the Stacker Offset Home Sensor in
the home position (High) within 500ms of the start of Offset Home recovery operation.
•
During Set Eject, the Control Logic does not detect the Stacker Offset Home Sensor in
the offset position (Low) within 300ms from the start of the offset cycle.
•
During Set Eject, the Control Logic does not detect the Stacker Offset Home Sensor in
the home position (High) within 300ms of the command to return to the home position.
Initial Actions
Refer to BSD 12.1 and BSD 12.14 for this procedure.
display
Procedure
Enter dC330 012-027 Eject Clamp/Offset Motor F/R. Press Start. The Eject Roll and Clamp
measured
move to the offset position and back to home.
Y
N
Switch off the power. Remove the rear covers. Manually rotate the shaft of the Eject
Clamp/Offset Motor
(PL
Y
N
Disassemble the gear cluster
Manually rotate the motor shaft The shaft moves freely.
Y
N
Replace the Eject Clamp/Offset Motor
Check the following:
•
Check the gears for damage or dirt that may cause binding
•
Check the Eject Roll
•
Check the Pinch Roll/Compiler Cover/Set Separator area for binding
18.20).
•
Ensure that the Offset Lever and Cam Follower
installed, and that the Cam follower is positioned in the spiral groove in the Off-
set Cam
(PL
The Eject Shaft moves front/rear as the motor shaft is rotated
Y
N
Check the following:
•
Check the gears for damage or dirt that may cause binding
•
Check the Eject Roll
•
Check the Pinch Roll/Compiler Cover/Set Separator area for binding
18.20).
•
Ensure that the Offset Lever and Cam Follower
installed, and that the Cam follower is positioned in the spiral groove in the Off-
set Cam
(PL
Go to
Flag 10
and
Flag 11
circuit to GND. If the wires are good, replace the Eject Clamp/Offset Motor
If the problem continues, replace the Finisher PWB
A
1/05
8d-41
18.21) clockwise. The shaft moves freely.
(PL
18.21) connected to the Eject Clamp/Offset Motor.
(PL
18.21).
(PL
18.19) for damage or binding.
(PL
18.21).
(PL
18.19) for damage or binding.
(PL
18.21).
on BSD 12.14. Check the wires for an open circuit or a short
(PL
18.4).
(PL
18.19) are correctly
(PL
18.19) are correctly
(PL
18.21).
Finisher/Sorter
12-245 , 12-246
Advertisement
Table of Contents
Troubleshooting
