Examples - HP ProCurve 5400zl Reference Manual

Command Line Interface Reference Guide
■
integer-codepoint
■
dscp
■
■
■
■
well-defined-codepoint
■
the device uses to prioritize IP traffic
dscp
■
■
■
■
ip-precedence
■
based on the upper 3 bits of the IP ToS field. The priority association is automatic and cannot
be changed: IP-Precedence 802.1p ToS Bits Priority -------------------------------- 111 7 (Highest) 110
6 101 5 100 4 011 3 010 0 (Normal) 001 2 (Low) 000 1 (Lowest)

EXAMPLES

Example: qos
The following example shows the 802.1p priority for the UDP and TCP port prioritization.
ProCurve(config)# qos tcp-port 23 priority 7
ProCurve(config)# qos udp-port 23 priority 7
ProCurve(config)# qos tcp-port 80 priority 2
ProCurve(config)# qos udp-port 80 priority 1
ProCurve(config)# qos udp-port range 100 199 priority 3
ProCurve(config)# show qos tcp-udp-port-priority
TCP/UDP port based priorities
| Application
Protocol | Port
-------- + ----------- ---------- + ------ -----------
TCP | 23
UDP | 23
TCP | 80
UDP | 80
UDP | 100-199
Example: qos
This example assigns the DSCP policies to the selected UDP/TCP port applications.
ProCurve(config)# qos udp-port 23 dscp 000111
ProCurve(config)# qos tcp-port 80 dscp 000101
ProCurve(config)# qos tcp-port 914 dscp 000010
ProCurve(config)# qos udp-port range 1001 2000 dscp 000010
ProCurve(config)# show qos tcp-udp-port-priority
TCP/UDP port based priorities
© 2009 Hewlett-Packard Development Company, L.P.
well-defined < af11 | af12 | af13 | ... > -- Define Differentiated Services Codepoint to
which to map IP ToS. (p. 434)
< 0 to 63 > -- Specify the DSCP code-point in decimal.
-- Define Differentiated Services Codepoint to which to map IP ToS.
binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal.
well-defined < af11 | af12 | af13 | ... > -- Define Differentiated Services Codepoint to
which to map IP ToS. (p. 434)
< af11 | af12 | af13 | ... > -- Configure the Type-of-Service method
-- Define Differentiated Services Codepoint to which to map IP ToS.
binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal.
well-defined < af11 | af12 | af13 | ... > -- Define Differentiated Services Codepoint to
which to map IP ToS. (p. 434)
-- In IP-Precedence mode, IPv4 packets are classified and given a QoS priority
Apply rule | DSCP
Priority
Priority
Priority
Priority
Priority
(p. 453)
|
Priority
| 7
| 7
| 2
| 1
| 3
(p. 422)
(p. 418)
(p. 423)
(p. 418)
(p. 423)
(p. 424)
qos
(p. 416)
(p. 416)
414