HP ProCurve 5400zl Reference Manual page 209

Command Line Interface Reference Guide
access-group
■
(p. 214)
direction
■
address
■
dhcp-bootp
■
(p. 230)
ip-addr
■
ipv6 -- Configure various IP parameters for the VLAN
■
address
■
autoconfig
■
dhcp
■
■
ipv6-addr
■
■
ipv6-addr/mask
■
(IPV6-ADDR/PREFIX-LEN)
■
■
enable
■
addr.
jumbo -- Labels this VLAN as a Jumbo VLAN, allowing you to pass packets up to 9220 bytes
■
in size (p. 246)
monitor
■
all < In | Out | Both > -- Monitor all traffic.
■
mirror
■
■
■
name -- Set the VLAN's name (ASCII-STR)
■
protocol
■
protocol-group
■
(ASCII-STR)
protocols
■
qos -- Set VLAN-based priority
■
dscp
■
binary-range
■
integer-range
■
well-defined
■
(Differentiated-Services Codepoint) value and an 802
priority
■
tagged -- Assign ports to current VLAN as tagged ([ethernet] PORT-LIST)
■
untagged
■
voice -- Labels this VLAN as a Voice VLAN, allowing you to separate, prioritize, and authenticate
■
voice traffic moving through your network
■ [no] interface
282)
auto -- Cause each port identified in the port list to learn its VLAN membership using the GARP
■
VLAN Registration Protocol (GVRP) ([ethernet] PORT-LIST)
connection-rate-filter
■
blocked by the connection rate filter
unblock
■
© 2009 Hewlett-Packard Development Company, L.P.
-- Apply the specified access control list on this VLAN interface (ASCII-STR)
< in | out | connection-rate-filter | ... > --
-- Set IP parameters for communication within an IP network
-- Configure the interface to use DHCP/Bootp server to acquire parameters.
-- Interface IP address/mask. (IP-ADDR/mask-LENGTH)
-- Set IPv6 parameters for communication within an IP network
-- Automatic address configuration.
-- Configure a DHCPv6 client.
full -- Obtain IPv6 address & Configuration information from DHCPv6 server.
rapid-commit -- Obtain IPv6 address quickly from DHCPv6 server.
■
-- Configure a link-local IPv6 address. (IPV6-ADDR)
link-local -- Configure a link-local IPv6 address.
-- Configure IPv6 address represented in CIDR notation.
anycast -- Address that is assigned to a set of interfaces that typically belong to
different nodes (p. 221)
eui-64 -- An IPv6 EUI-64 address that can be automatically configured on any interface
(p. 232)
-- Enable IPv6 on an interface and configures an automatically generated link-local
(p. 232)
-- Define either the VLAN is to be monitored or not
-- Mirror destination.
mirror_session_name
monitor_mirror_session_id
-- Set a predefined protocol for the current VLAN.
-- Enter a list of protocols for the current VLAN delimited by commas.
(p. 267)
< IPX | IPv4 | IPv6 | ... > -- Set a predefined protocol for the current VLAN.
-- Specify DSCP policy to use.
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
< 0 to 63 > -- Specify the DSCP code-point in decimal.
< af11 | af12 | af13 | ... > -- Define mapping between a DSCP
< 0 | 1 | 2 | ... > -- Specify priority to use.
-- Assign ports to current VLAN as untagged ([ethernet] PORT-LIST)
vlan -- Add, delete, edit VLAN configuration or enter a VLAN context (VLAN-ID)
-- Re-enables access to a host or set of hosts that has been previously
-- Resets a host previously blocked by the connection rate filter
(p. 230)
(p. 245)
(p. 219)
(p. 251)
-- Mirror destination name.
< 1 to 4 > -- Mirror destination number.
(p. 254)
(p. 268)
(p. 231)
(p. 265)
(p. 283)
(p. 228)
(p. 231)
(p. 216)
(p. 241)
(p. 244)
(p. 216)
(p. 225)
(p. 245)
(p. 248)
(p. 252)
(p. 251)
(p. 266)
(p. 239)
(p. 285)
(p. 278)
(p. 225)
(p. 281)
interface
(p. 235)
(p. 271)
(p. 254)
(p. 267)
(p. 227)
(p. 282)
(p.
207