Command Line Interface Reference Guide
server-address
■
priority
■
ip6addr
■
ipaddr
■
■ [no] ip
icmp
addrmask
■
burst-normal
■
(p. 296)
echo
-- Enable/disable echo replies to broadcast echo requests
■
broadcast-request
■
(p. 296)
redirects
■
reply-limit
■
unreachable
■
■ [no] ip
igmp
auto
-- Instruct the device to monitor incoming multicast traffic on the specified ports (this is
■
the default behavior) ([ethernet] PORT-LIST)
blocked
■
ports ([ethernet] PORT-LIST)
fastleave
■
forcedfastleave
■
port is cascaded ([ethernet] PORT-LIST)
forward
■
ports ([ethernet] PORT-LIST)
high-priority-forward
■
Multicast groups
querier
-- Specify querier/non-querier capability for the VLAN
■
interval
■
301)
■ [no] ip
irdp
■ [no] ip
load-sharing
load-sharing-value
■
paths
(p. 303)
■ [no] ip
multicast-routing
■ ip
preserve
■ [no] ip
route
ip-addr
-- Specify IP address and mask of the route destination. (IP-ADDR/MASK-LENGTH)
■
302)
blackhole
■
distance
■
(p. 298)
ip-addr
■
distance
■
(p. 298)
reject
■
distance
■
(p. 298)
vlan
-- Specify the destination VLAN. (VLAN-ID)
■
distance
■
(p. 298)
■ [no] ip
router-id
ipaddr
-- Define the device router id (IP-ADDR)
■
■ [no] ip
routing
© 2009 Hewlett-Packard Development Company, L.P.
-- Configure DNS server IP address.
< 1 to 2 > -- Priority of Server Address. (NUMBER)
-- DNS server IPv6 address. (IPV6-ADDR)
-- DNS server IP address. (IP-ADDR)
-- Configure ICMP Rate Limiting capacity
-- Enable/disable address mask replies
< 0 to 1000000 > -- The maximum number of icmp replies to send per second
< Min | Max > -- Enable/disable echo replies to broadcast echo requests
-- Enable/disable redirect error messages
-- Enable/disable ICMP reply rate limiting
-- Enable/disable destination unreachable error messages
-- Enable/disable/configure IP Multicast Group Protocol (IGMP) feature
-- Instruct the device to drop incoming multicast packets received on the specified
(p. 296)
-- Enables or disables IGMP Fast Leaves ([ethernet] PORT-LIST)
-- When enabled, this feature forces IGMP Fast Leaves to occur even when the
-- Instruct the device to forward incoming multicast packets received on the specified
(p. 300)
-- Enable/disable the high priority forwarding of traffic for subscribed IP
(p. 300)
< 5 to 300 > -- Sets the interval in seconds between IGMP queries (default: 125)
-- Enable/disable ICMP Router Discovery Protocol (IRDP)
-- Specify the maximum number of equal cost IP load sharing paths
< 2 to 4 > -- Specify the maximum number of equal cost IP load sharing
-- Enable/disable IP multicast routing on the device
--
(p. 305)
-- Add or delete static routing table entries
-- Specify that packets are silently discarded with no ICMP message sent.
< 1 to 255 > -- Set the administrative distance to associate with this static route.
-- Specify gateway IP address. (IP-ADDR)
< 1 to 255 > -- Set the administrative distance to associate with this static route.
-- Specify that packets are discarded and ICMP error is returned to sender.
< 1 to 255 > -- Set the administrative distance to associate with this static route.
< 1 to 255 > -- Set the administrative distance to associate with this static route.
-- Define the device router id
-- Enable/disable IP routing support on the device
(p. 308)
(p. 302)
(p. 302)
(p. 300)
(p. 294)
(p. 306)
(p. 306)
(p. 296)
(p. 299)
(p. 306)
(p. 307)
(p. 302)
(p. 312)
(p. 307)
(p. 302)
(p. 308)
(p. 305)
(p. 299)
(p. 312)
(p. 300)
(p. 299)
(p. 303)
(p. 304)
(p. 306)
ip
(p.
(p. 303)
(p.
(p. 296)
291