HP ProCurve 5400zl Reference Manual page 213

Command Line Interface Reference Guide
rip -- Enable/disable/configure Routing Internet Protocol (RIP) on the VLAN interface
■
all
■
■
■
■
■
■
■
■
authentication-key
■
■
authentication-type
■
224)
ip-addr
■
■
■
■
■
■
■
■
metric
■
poison-reverse
■
receive
■
(p. 273)
rip-compatible
■
outgoing packets.
send
■
packets.
ip-recv-mac-address
■
mac-address
■
interval
■
■
ipv6 -- Configure various IP parameters for the VLAN
■
access-group
■
vlan
■
address
■
autoconfig
■
dhcp
■
■
© 2009 Hewlett-Packard Development Company, L.P.
-- Process the request for all IP addresses.
authentication-key -- Set RIP authentication key (maximum 16 characters).
auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
■
(p. 225)
authentication-type < none | text > -- Set authentication type used on this interface.
(p. 224)
metric < 1 to 15 > -- Set metric for this interface.
poison-reverse -- Enable/disable poison reverse on this interface.
receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
(p. 273)
rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming
and outgoing packets.
send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 275)
-- Set RIP authentication key (maximum 16 characters).
auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
(p. 225)
< none | text > -- Set authentication type used on this interface.
-- Specify the IP address the request is for. (IP-ADDR)
authentication-key -- Set RIP authentication key (maximum 16 characters).
auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
■
(p. 225)
authentication-type < none | text > -- Set authentication type used on this interface.
(p. 224)
metric < 1 to 15 > -- Set metric for this interface.
poison-reverse -- Enable/disable poison reverse on this interface.
receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
(p. 273)
rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming
and outgoing packets.
send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 275)
< 1 to 15 > -- Set metric for this interface.
-- Enable/disable poison reverse on this interface.
< V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
< V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming and
(p. 274)
< disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
(p. 275)
-- Associates a L3-mac-address with a VLAN
-- The L3-mac-address to be associated with a VLAN. (MAC-ADDR)
-- Specify the L3-Mac-Address timeout interval.
timer-interval < 1 to 255 > -- Timeout interval in seconds <1-255>.
-- Apply a IPV6 ACl on a VLAN (ASCII-STR)
-- VLAN acl. (p. 282)
-- Set IPv6 parameters for communication within an IP network
-- Automatic address configuration.
-- Configure a DHCPv6 client.
full -- Obtain IPv6 address & Configuration information from DHCPv6 server.
(p. 219)
(p. 274)
(p. 274)
(p. 244)
(p. 225)
(p. 230)
(p. 250)
(p. 262)
(p. 241)
(p. 250)
(p. 262)
(p. 250)
(p. 262)
(p. 243)
(p. 240)
(p. 278)
(p. 214)
(p. 216)
interface
(p. 274)
(p. 223)
(p. 223)
(p.
(p. 223)
(p. 249)
(p. 235)
211