HP ProCurve 5400zl Reference Manual page 211

Command Line Interface Reference Guide
■
■
local-proxy-arp
■
mroute
■
ttl-threshold
■
(p. 279)
ospf
■
interface
all
■
■
■
■
■
■
■
■
■
■
■
■
area
■
■
■
authentication
■
authentication-key
■
■
cost
■
dead-interval
■
hello-interval
■
ip-addr
■
■
■
■
■
■
■
■
© 2009 Hewlett-Packard Development Company, L.P.
no-default -- Indicates that the router should never be used as a default by its
neighbors. (p. 255)
number < -2147483647 to 2147483647 > -- The router preferability number. Higher
values are more preferable.
-- Enable/disable local proxy ARP
-- Configure IP Multicast Routing parameters on the VLAN interface
< 0 to 255 > -- Set the multicast datagram TTL threshold for the interface
-- Enable/disable/configure Open Shortest Path First (OSPF) protocol on the VLAN
(p. 256)
-- Process the request for all IP addresses.
area -- Specify an OSPF area.
area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID)
■
222)
backbone -- The backbone area (the same as 0.0.0.0).
■
authentication -- Disable authentication.
authentication-key -- Set simple authentication method and key.
authentication-key
■
(OCTET-STR) (p. 223)
cost < 1 to 65535 > -- Set metric of this interface.
dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40.
hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10.
md5-auth-key-chain
chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR)
■
228)
passive -- Configures an ospf interface as passive.
priority < 0 to 255 > -- Set priority of this router as a designated router.
retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is
5. (p. 273)
transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1.
-- Specify an OSPF area.
area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID)
backbone -- The backbone area (the same as 0.0.0.0).
-- Disable authentication.
-- Set simple authentication method and key.
authentication-key -- OSPF authentication key (maximum 8 characters). (OCTET-STR)
(p. 223)
< 1 to 65535 > -- Set metric of this interface.
< 1 to 65535 > -- Set dead interval in seconds; the default is 40.
< 1 to 65535 > -- Set hello interval in seconds; the default is 10.
-- Specify the IP address the request is for. (IP-ADDR)
area -- Specify an OSPF area.
area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID)
■
222)
backbone -- The backbone area (the same as 0.0.0.0).
■
authentication -- Disable authentication.
authentication-key -- Set simple authentication method and key.
authentication-key
■
(OCTET-STR) (p. 223)
cost < 1 to 65535 > -- Set metric of this interface.
dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40.
hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10.
md5-auth-key-chain
(p. 256)
(p. 219)
(p. 221)
(p. 223)
-- OSPF authentication key (maximum 8 characters).
-- Set MD5 authentication method and key chain.
(p. 221)
(p. 223)
(p. 221)
(p. 223)
-- OSPF authentication key (maximum 8 characters).
-- Set MD5 authentication method and key chain.
(p. 248)
(p. 226)
(p. 223)
(p. 229)
(p. 258)
(p. 226)
(p. 223)
(p. 229)
(p. 241)
(p. 226)
(p. 223)
(p. 229)
interface
(p. 254)
(p.
(p. 229)
(p. 236)
(p. 250)
(p.
(p. 265)
(p. 279)
(p. 222)
(p. 229)
(p. 236)
(p.
(p. 229)
(p. 236)
(p. 250)
209