Command Line Interface Reference Guide
type
■
600)
neighbor
■
neighbor-ip
■
redistribute
■
restrict
■
spf-log
■
last ten Reasons for running SPF
statistics
■
OSPF enabled interfaces
if-ip
■
(IP-ADDR)
vlan
■
(p. 603)
traps
■
virtual-link
■
area
■
vlink-ip
■
(IP-ADDR)
virtual-neighbor
■
area
■
vneighbor-ip
■
(IP-ADDR)
pim
-- Show PIM protocol operational and configuration information
■
bsr
-- Show Bootstrap Router information
■
elected
■
local
■
interface
■
VLAN-ID
■
mroute
■
IP-ADDR
■
■
neighbor
■
IP-ADDR
■
pending
■
rp-candidate
■
config
■
rp-pending
■
rp-set
■
learned
■
static
■
rip
-- Show RIP operational and configuration information
■
general
■
interface
■
if-ip
■
(IP-ADDR)
vlan
■
(p. 603)
peer
■
peer-ip
■
redistribute
■
restrict
■
route
-- Show the IP routing table
■
© 2009 Hewlett-Packard Development Company, L.P.
< router | network | summary | ... > -- Show LSAs of the specified type only.
-- Show all OSPF neighbors in the locality of of the device
-- (IP-ADDR)
-- List protocols which are being redistributed into OSPF
-- List routes which will not be redistributed via OSPF
-- List the OSPF SPF(Shortes Path First Algorithm) run count for all OSPF areas and
-- List OSPF packet statistics( OSPF sent,recieved and error packet count) of all
(p. 594)
-- Specify IP address of the interface for which to show detailed information.
(p. 556)
-- Specify VLAN of the interface for which to show detailed information. (VLAN-ID)
-- Show OSPF traps enabled on the device
-- Show status of all OSPF virtual links configured
-- Specify area of the virtual links to show. (OSPF-AREA-ID)
-- Router ID of the link destination for which to show detailed information.
(p. 608)
-- Show all virtual neighbors of the device
-- Specify area of the virtual neighbors to show. (OSPF-AREA-ID)
-- Router ID of the virtual neighbor for which to show detailed information.
(p. 608)
-- Show elected Bootstrap Router information.
-- Show local Candidate-BSR configuration information.
-- Show PIM interface information
-- Specify the VLAN ID of the PIM interface to show. (VLAN-ID)
-- Show PIM-specific information from the IP multicast routing table
-- Specify the IP multicast group address of the MRT entry. (IP-ADDR)
IP-ADDR
-- Specify the source IP address of the MRT entry. (IP-ADDR)
-- Show PIM neighbor information
-- Specify the IP address of the PIM neighbor to show. (IP-ADDR)
-- Show (*,G) and (S,G) Join Pending Information.
-- Show Candidate-RP operational and configuration information
-- Show C-RP configuration information.
-- Show (*,*,RP) Join Pending Information.
-- Show RP-Set information available on the router
-- Show RP-Set information learned from the BSR.
-- Show statically configured RP-Set information.
-- Show RIP basic configuration and operational information
-- Show RIP interfaces' information
-- Specify IP address of the interface for which to show detailed information.
(p. 556)
-- Specify VLAN of the interface for which to show detailed information. (VLAN-ID)
-- Show RIP peers
(p. 575)
-- Specify IP address of the RIP peer to show. (IP-ADDR)
-- List protocols which are being redistributed into RIP
-- List routes which will not be redistributed via RIP
(p. 573)
(p. 593)
(p. 599)
(p. 535)
(p. 559)
(p. 573)
(p. 559)
(p. 587)
(p. 573)
(p. 584)
(p. 586)
(p. 603)
(p. 529)
(p. 603)
(p. 576)
(p. 550)
(p. 566)
(p. 576)
(p. 540)
(p. 588)
(p. 588)
(p. 565)
(p. 594)
(p. 586)
(p. 553)
(p. 576)
(p. 584)
(p. 586)
show
(p.
(p. 529)
(p. 607)
(p. 571)
(p. 562)
(p. 562)
(p. 562)
(p. 588)
515