Command Line Interface Reference Guide
receive
■
(p. 745)
rip-compatible
■
outgoing packets.
send
■
packets.
metric
■
poison-reverse
■
receive
■
745)
rip-compatible
■
outgoing packets.
send
■
packets.
■ [no] vlan VLAN-ID
mac-address
■
interval
■
timer-interval
■
■ vlan VLAN-ID
access-group
■
vlan
-- VLAN acl.
■
address
■
autoconfig
■
dhcp
■
full
■
■
ipv6-addr
■
link-local
■
ipv6-addr/mask
■
(IPV6-ADDR/PREFIX-LEN)
anycast
■
nodes
eui-64
■
(p. 723)
enable
-- Enable IPv6 on an interface and configures an automatically generated link-local addr.
■
(p. 723)
mld
-- Enable/disable/configure IPv6 Multicast Listener Discovery (MLD) feature on a VLAN
■
735)
auto
■
is the default behavior) ([ethernet] PORT-LIST)
blocked
■
ports ([ethernet] PORT-LIST)
fastleave
■
PORT-LIST)
forcedfastleave
■
VLAN, even if they are cascaded ([ethernet] PORT-LIST)
forward
■
ports ([ethernet] PORT-LIST)
querier
■
if necessary
nd
-- IPv6 nodes on the same link use Neighbor Discovery to discover each other's presence,
■
link-layer addresses, routers and to maintain reachability information about the paths to active
neighbors
© 2009 Hewlett-Packard Development Company, L.P.
< V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
< V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming and
(p. 747)
< disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
(p. 747)
< 1 to 15 > -- Set metric for this interface.
-- Enable/disable poison reverse on this interface.
< V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
< V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming and
(p. 747)
< disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
(p. 747)
ip-recv-mac-address
-- The L3-mac-address to be associated with a VLAN. (MAC-ADDR)
-- Specify the L3-Mac-Address timeout interval.
< 1 to 255 > -- Timeout interval in seconds <1-255>.
ipv6
-- Configure various IP parameters for the VLAN
-- Apply a IPV6 ACl on a VLAN (ASCII-STR)
(p. 750)
-- Set IPv6 parameters for communication within an IP network
-- Automatic address configuration.
-- Configure a DHCPv6 client.
-- Obtain IPv6 address & Configuration information from DHCPv6 server.
rapid-commit
-- Obtain IPv6 address quickly from DHCPv6 server.
-- Configure a link-local IPv6 address. (IPV6-ADDR)
-- Configure a link-local IPv6 address.
-- Configure IPv6 address represented in CIDR notation.
(p. 732)
-- Address that is assigned to a set of interfaces that typically belong to different
(p. 716)
-- An IPv6 EUI-64 address that can be automatically configured on any interface
-- Instruct the device to monitor incoming multicast traffic on the specified ports (this
-- Instruct the device to drop incoming multicast packets received on the specified
-- Enables MLD fast-leaves on the specified ports in the selected VLAN ([ethernet]
(p. 723)
-- Enables MLD Forced Fast-Leave on the specified ports in the selected
-- Instruct the device to forward incoming multicast packets received on the specified
-- This command disables or re-enables the ability for the switch to become querier
(p. 744)
(p. 737)
(p. 734)
-- Associates a L3-mac-address with a VLAN
(p. 719)
(p. 722)
(p. 733)
(p. 719)
(p. 720)
(p. 724)
(p. 741)
(p. 728)
(p. 748)
(p. 731)
(p. 713)
(p. 713)
(p. 745)
(p. 731)
(p. 724)
vlan
(p.
(p. 731)
(p. 733)
(p. 725)
(p.
710