Command Line Interface Reference Guide
well-defined
■
(Differentiated-Services Codepoint) value and an 802
priority
■
ipv6
-- specify the ipv6 address of the device to set the priority (IPV6-ADDR)
■
dscp
■
binary-range
■
integer-range
■
well-defined
■
(Differentiated-Services Codepoint) value and an 802
priority
■
ipv6/mask
■
(IPV6-ADDR/PREFIX-LEN)
dscp
■
binary-range
■
integer-range
■
well-defined
■
(Differentiated-Services Codepoint) value and an 802
priority
■
■ [no] qos
dscp-map
and an 802
binary-range
■
name
■
name-string
■
priority
■
integer-range
■
name
■
name-string
■
priority
■
well-defined
■
Codepoint) value and an 802
name
■
name-string
■
priority
■
■ [no] qos
protocol
priority
< 0 | 1 | 2 | ... > -- Specify priority to use.
■
■ qos
queue-config
on their 802
2-queues
■
4-queues
■
8-queues
■
■ [no] qos
type-of-service
traffic
(p. 433)
diff-services
■
given a QoS priority based on the upper 6 bits of the IP ToS field from the packets as they enter
the switch. The assignment of Diffserv Codepoints to 802.1p priorities is done via the qos
dscp-map command. Any Diffserv Codepoint in an inbound IPv4 packet can be re-mapped to
a different codepoint (and its associated 802.1p priority) on outbound. This is done by using
the syntax: qos type-of-service diff-services <af11..ef|0-63|000000...111111> dscp
<af11..ef|0-63|000000...111111>
binary-codepoint
■
dscp
■
■
■
© 2009 Hewlett-Packard Development Company, L.P.
< af11 | af12 | af13 | ... > -- Define mapping between a DSCP
< 0 | 1 | 2 | ... > -- Specify priority to use.
-- Specify DSCP policy to use.
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
< 0 to 63 > -- Specify the DSCP code-point in decimal.
< af11 | af12 | af13 | ... > -- Define mapping between a DSCP
< 0 | 1 | 2 | ... > -- Specify priority to use.
-- specify the ipv6 address with prefix-length of the device to set the priority
(p. 425)
-- Specify DSCP policy to use.
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
< 0 to 63 > -- Specify the DSCP code-point in decimal.
< af11 | af12 | af13 | ... > -- Define mapping between a DSCP
< 0 | 1 | 2 | ... > -- Specify priority to use.
-- Define mapping between a DSCP (Differentiated-Services Codepoint) value
(p. 421)
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
-- Specify DSCP->priority mapping name.
-- Specify DSCP->priority mapping name. (ASCII-STR)
< 0 | 1 | 2 | ... > -- Specify priority to use.
< 0 to 63 > -- Specify the DSCP code-point in decimal.
-- Specify DSCP->priority mapping name.
-- Specify DSCP->priority mapping name. (ASCII-STR)
< 0 | 1 | 2 | ... > -- Specify priority to use.
< af11 | af12 | af13 | ... > -- Define mapping between a DSCP (Differentiated-Services
(p. 434)
-- Specify DSCP->priority mapping name.
-- Specify DSCP->priority mapping name. (ASCII-STR)
< 0 | 1 | 2 | ... > -- Specify priority to use.
< IP | IPX | ARP | ... > -- Configure protocol-based priority
-- Sets the number of outbound port queues that buffer the packets depending
(p. 432)
-- Set the number of outbound port queues for all switch ports.
-- Set the number of outbound port queues for all switch ports.
-- Set the number of outbound port queues for all switch ports.
-- Configure the Type-of-Service method the device uses to prioritize IP
-- In IP Differentiated Services (Diffserv) mode, IPv4 packets are classified and
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
-- Define Differentiated Services Codepoint to which to map IP ToS.
binary-range
< 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
integer-range
< 0 to 63 > -- Specify the DSCP code-point in decimal.
(p. 428)
(p. 418)
(p. 428)
(p. 418)
(p. 428)
(p. 426)
(p. 428)
(p. 426)
(p. 428)
(p. 426)
(p. 428)
(p. 428)
(p. 418)
(p. 434)
(p. 425)
(p. 423)
(p. 434)
(p. 423)
(p. 434)
(p. 416)
(p. 426)
(p. 423)
(p. 426)
(p. 426)
(p. 431)
(p. 415)
(p. 415)
(p. 415)
(p. 418)
(p. 423)
qos
(p. 416)
(p. 416)
(p. 416)
(p. 416)
413