Command Structure - HP ProCurve 5400zl Reference Manual

Command Line Interface Reference Guide
o priority <0-15> or <0-65535> (default is 32768 and step 8 respectively) -
The device priority - used along with the switch MAC address to determine
which device is the root. If 802.1w or 802.1s STP version is set, then
the range of 0-61440 is divided into steps of 4096. These steps are
numbered from 0 to 15.
o config-name ASCII-STR (default is switch's MAC address) - The name of
the MST region configuration identifier. The name has the maximum length
of 32 characters and is case sensitive. Use "no" form of the command
to reset to the default name. The parameter is configurable in MSTP mode
only.
o config-revision <0-65535> (default is 0) - The revision number of the MST
region configuration identifier. The parameter is configurable in MSTP
mode only.
o max-hops <1-40> (default is 20) - The number of hops in the MST region
before the MST BPDU is discarded and the information held for a port is
aged. This parameter is configurable in MSTP mode only and serves for
the same purpose as the maximum-age and message-age couple used by
legacy single spanning tree bridges.
o instance ... - Allows to create, delete and configure MST instances.
This command is available in MSTP mode only. See the command help for
further details.
o pending ... - Manipulate the pending MSTP configuration. This command
is available in MSTP mode only. See the command help for more details.
o legacy-path-cost - Set default pathcosts to 802.1D (legacy)
(not legacy) values. This command is available in MSTP mode only.
o legacy-mode - Set spanning-tree protocol to operate either in 802.1D
legacy mode or in 802.1s native mode. This command is available in MSTP
mode only. See the command help for more details.
o trap - Enable/disable STP traps. The following traps are generated
-

COMMAND STRUCTURE

■ spanning-tree
down state after receiving unauthorized BPDUs.
■ spanning-tree
instance
■
ports
■
ports -- Clear spanning tree port(s) debug counters. ([ethernet] PORT-LIST)
■
instance
■
■ [no] spanning-tree
MAC address).
config-name
■
■ spanning-tree
(default is 0).
■ spanning-tree
compatibility mode.
■ spanning-tree
Tree protocol compatibility mode.
■ spanning-tree
listening to learning and from learning to forwarding states.
■ spanning-tree
is root. (p. 643)
■ spanning-tree
© 2009 Hewlett-Packard Development Company, L.P.
as a result of finding an unusual condition on a switch port.
Possible trap names are:
'errant-bpdu' signifies that an unexpected Spanning Tree BPDU
has been received on a port.
bpdu-protection-timeout
clear-debug-counters
< 0 to 16 > -- Clear spanning tree instance debug counters. (NUMBER)
-- Clear spanning tree port(s) debug counters. ([ethernet] PORT-LIST)
< 0 to 16 > -- Clear spanning tree instance debug counters. (NUMBER)
config-name -- Set the MST region configuration name (default is switch's
(p. 642)
-- Specify the configuration name (maximum 32 characters). (ASCII-STR)
config-revision < 0 to 65535 > -- Set the MST region configuration revision number
(p. 642)
force-version < STP-compatible | RSTP-operation > -- Set Spanning Tree protocol
(p. 642)
force-version < STP-compatible | RSTP-operation | MSTP-operation > -- Set Spanning
forward-delay < 4 to 30 > -- Set time the switch waits between transitioning from
hello-time < 1 to 10 > -- Set time between messages transmission when the switch
instance -- Create, delete or configure an MST instance
< 0 to 65535 > -- Set the time for protected ports to be in
(p. 641)
-- Clear spanning tree debug counters.
(p. 642)
or 802.1t
(p. 642)
(p. 651)
(p. 651)
(p. 643)
(p. 643)
spanning-tree
(p. 643)
(p. 643)
(p. 642)
638