Command Line Interface Reference Guide
ipv6-addr
■
■
ipv6-addr/mask
■
(IPV6-ADDR/PREFIX-LEN)
■
■
enable
■
addr.
mld
-- Enable/disable/configure IPv6 Multicast Listener Discovery (MLD) feature on a VLAN
■
(p. 251)
auto
■
(this is the default behavior) ([ethernet] PORT-LIST)
blocked
■
ports ([ethernet] PORT-LIST)
fastleave
■
([ethernet] PORT-LIST)
forcedfastleave
■
VLAN, even if they are cascaded ([ethernet] PORT-LIST)
forward
■
specified ports ([ethernet] PORT-LIST)
querier
■
querier if necessary
nd
-- IPv6 nodes on the same link use Neighbor Discovery to discover each other's presence,
■
link-layer addresses, routers and to maintain reachability information about the paths to
active neighbors
ns-interval
■
requests sent for an unresolved destination, or between duplicate address detection
neighbor solicitation requests
■
reachable-time
■
being confirmed as reachable via the neighbor unreachability detection algorithm
273)
■
jumbo
-- Labels this VLAN as a Jumbo VLAN, allowing you to pass packets up to 9220 bytes
■
in size
(p. 246)
monitor
■
all
< In | Out | Both > -- Monitor all traffic.
■
mirror
■
■
■
name
-- Set the VLAN's name (ASCII-STR)
■
protocol
■
protocol-group
■
(ASCII-STR)
protocols
■
qos
-- Set VLAN-based priority
■
dscp
■
© 2009 Hewlett-Packard Development Company, L.P.
rapid-commit
-- Obtain IPv6 address quickly from DHCPv6 server.
■
-- Configure a link-local IPv6 address. (IPV6-ADDR)
link-local
-- Configure a link-local IPv6 address.
-- Configure IPv6 address represented in CIDR notation.
anycast
-- Address that is assigned to a set of interfaces that typically belong to
different nodes
(p. 221)
eui-64
-- An IPv6 EUI-64 address that can be automatically configured on any interface
(p. 232)
-- Enable IPv6 on an interface and configures an automatically generated link-local
(p. 232)
-- Instruct the device to monitor incoming multicast traffic on the specified ports
-- Instruct the device to drop incoming multicast packets received on the specified
-- Enables MLD fast-leaves on the specified ports in the selected VLAN
(p. 233)
-- Enables MLD Forced Fast-Leave on the specified ports in the selected
-- Instruct the device to forward incoming multicast packets received on the
-- This command disables or re-enables the ability for the switch to become
(p. 269)
(p. 255)
-- Configures the neighbor discovery time between neighbor solicitation
number
< 1000 to 3600000 > -- Configures the neighbor discovery time between
neighbor solicitation requests sent for an unresolved destination, or between duplicate
address detection neighbor solicitation requests
-- Configures the length of time neighbors are considered reachable after
number
< 1000 to 3600000 > -- Configures the router lifetime sent in router
advertisements
(p. 256)
-- Define either the VLAN is to be monitored or not
-- Mirror destination.
mirror_session_name
monitor_mirror_session_id
-- Set a predefined protocol for the current VLAN.
-- Enter a list of protocols for the current VLAN delimited by commas.
(p. 267)
< IPX | IPv4 | IPv6 | ... > -- Set a predefined protocol for the current VLAN.
-- Specify DSCP policy to use.
(p. 245)
(p. 227)
(p. 234)
(p. 256)
(p. 219)
(p. 251)
-- Mirror destination name.
< 1 to 4 > -- Mirror destination number.
(p. 254)
(p. 268)
(p. 231)
(p. 271)
(p. 245)
(p. 248)
(p. 225)
(p. 234)
(p. 256)
(p. 252)
(p. 251)
(p. 254)
(p. 266)
interface
(p.
(p. 267)
212