Command Line Interface Reference Guide
udp
-- Add or remove a UDP server address for the VLAN
■
ip-addr
■
■
■
helper-address
■
igmp
-- Enable/disable/configure IP Multicast Group Protocol (IGMP) feature on a VLAN
■
auto
■
is the default behavior) ([ethernet] PORT-LIST)
blocked
■
ports ([ethernet] PORT-LIST)
fastleave
■
forcedfastleave
■
the port is cascaded ([ethernet] PORT-LIST)
forward
■
ports ([ethernet] PORT-LIST)
high-priority-forward
■
IP Multicast groups
querier
■
interval
■
(p. 728)
irdp
-- Configure ICMP Router Discovery Protocol (IRDP)
■
advert-address
■
router advertisements
holdtime
■
this interface
maxadvertinterval
■
sending unsolicited router advertisements
minadvertinterval
■
sending unsolicited router advertisements
preference
■
on the same subnet
no-default
■
(p. 737)
number
■
are more preferable.
local-proxy-arp
■
mroute
-- Configure IP Multicast Routing parameters on the VLAN interface
■
ttl-threshold
■
749)
ospf
-- Enable/disable/configure Open Shortest Path First (OSPF) protocol on the VLAN interface
■
(p. 738)
all
-- Process the request for all IP addresses.
■
area
■
■
■
authentication
■
authentication-key
■
■
cost
■
dead-interval
■
hello-interval
■
md5-auth-key-chain
■
© 2009 Hewlett-Packard Development Company, L.P.
-- IP address of the protocol server. (IP-ADDR)
port-name
< dns | ntp | netbios-ns | ... > -- (NUMBER)
port-num
-- UDP port number of the server. (TCP/UDP-PORT)
-- Add or remove a DHCP server IP address for the VLAN (IP-ADDR)
-- Instruct the device to monitor incoming multicast traffic on the specified ports (this
-- Instruct the device to drop incoming multicast packets received on the specified
-- Enables or disables IGMP Fast Leaves ([ethernet] PORT-LIST)
-- When enabled, this feature forces IGMP Fast Leaves to occur even when
-- Instruct the device to forward incoming multicast packets received on the specified
-- Enable/disable the high priority forwarding of traffic for subscribed
(p. 726)
-- Specify querier/non-querier capability for the VLAN
< 5 to 300 > -- Sets the interval in seconds between IGMP queries (default: 125)
< multicast | broadcast > -- Specify the destination address to be used for
(p. 714)
< 4 to 9000 > -- Set the lifetime (in seconds) of the router advertisements sent on
(p. 726)
< 4 to 1800 > -- Set the maximum time (in seconds) allowed between
< 3 to 1800 > -- Set the minimum time (in seconds) allowed between
-- The preferability of the router as a default router, relative to the other routers
(p. 742)
-- Indicates that the router should never be used as a default by its neighbors.
< -2147483647 to 2147483647 > -- The router preferability number. Higher values
(p. 738)
-- Enable/disable local proxy ARP
< 0 to 255 > -- Set the multicast datagram TTL threshold for the interface
-- Specify an OSPF area.
area-id
-- Single integer or IP address style dotted decimal. (OSPF-AREA-ID)
backbone
-- The backbone area (the same as 0.0.0.0).
-- Disable authentication.
-- Set simple authentication method and key.
authentication-key
-- OSPF authentication key (maximum 8 characters). (OCTET-STR)
(p. 717)
< 1 to 65535 > -- Set metric of this interface.
< 1 to 65535 > -- Set dead interval in seconds; the default is 40.
< 1 to 65535 > -- Set hello interval in seconds; the default is 10.
-- Set MD5 authentication method and key chain.
(p. 719)
(p. 720)
(p. 724)
(p. 724)
(p. 733)
(p. 735)
(p. 733)
(p. 715)
(p. 716)
(p. 717)
(p. 749)
(p. 729)
(p. 741)
(p. 741)
(p. 723)
(p. 744)
(p. 732)
(p. 736)
(p. 719)
(p. 717)
(p. 721)
(p. 734)
vlan
(p. 726)
(p. 727)
(p.
(p. 717)
(p. 721)
(p. 725)
707