Command Line Interface Reference Guide
broadcast-limit
■
dhcp-snooping
■
trust
■
disable
-- Disable port(s)
■
enable
-- Enable port(s)
■
flow-control
■
gvrp
-- Set the GVRP timers on the port (hundredths of a second)
■
join-timer
■
leaveall-timer
■
248)
leave-timer
■
ip
-- Apply the specified access control list to inbound packets on this INTERFACE list
■
access-group
■
list (ASCII-STR)
direction
■
source-lockdown
■
ipv6
-- Configure various IP parameters for the VLAN
■
access-group
■
in
■
lacp
-- Define whether LACP is enabled on the port, and whether it is in active or passive mode
■
when enabled
mode
■
is in active or passive mode when enabled
link-keepalive
■
vlan
-- Set vlan-id for tagged UDLD control packets. (VLAN-ID)
■
mdix-mode
■
monitor
■
all
< In | Out | Both > -- Monitor all traffic.
■
mirror
■
■
■
name
-- Set/unset a name for the port(s)
■
port-name
■
poe-allocate-by
■
allocate_by
■
221)
poe-lldp-detect
■
link-partner's capabilities via LLDP
poe_lldp_detect
■
power based on the link-partner's capabilities via LLDP
poe-value
■
poe_value
■
power-over-ethernet
■
priority
■
qinq
-- Configure a port's type as customer-network or provider-network
■
port-type
■
customer-network
■
© 2009 Hewlett-Packard Development Company, L.P.
queue4
< 0 to 100 > -- Specify min. bandwidth percentage for queue four
■
outgoing traffic.
queue5
< 0 to 100 > -- Specify min. bandwidth percentage for queue five
■
outgoing traffic.
■ additional options available...
< 0 to 99 > -- Set a broadcast traffic percentage limit
-- Configure the port as trusted or untrusted
-- Configure trusted interfaces
(p. 231)
(p. 232)
-- Enable/disable flow control on the port(s)
< 20 to 75 > -- Set join timer value (centiseconds; default 20).
< 500 to 3000 > -- Set leaveall timer value (centiseconds; default 1000).
< 40 to 300 > -- Set leave timer value (centiseconds; default 300).
-- Apply the specified access control list to inbound packets on this INTERFACE
(p. 214)
< in > --
(p. 231)
-- Enable/disable IP source lockdown in global configuration mode
-- Apply a IPV6 ACl on the interface (ASCII-STR)
-- Match inbound packets.
(p. 247)
< Active | Passive > -- Define whether LACP is enabled on the port, and whether it
-- Configure UDLD on port(s)
< mdi | mdix | autoMDIX > -- Set port MDI/MDIX mode (default: auto).
-- Define either the port is to be monitored or not
-- Mirror destination.
mirror_session_name
monitor_mirror_session_id
no-tag-added
-- Don't add VLAN tag for this untagged-port
■
-- Specify a port name up to 64 characters length. (ASCII-STR)
-- Control manual power over ethernet allocation
< usage | class | value > -- Control manual power over ethernet allocation
-- Enabling this feature causes the port to allocate power based on the
< disabled | enabled > -- Enabling this feature causes the port to allocate
-- Maximum PoE allocation specified with a value in watts
< 1 | 2 | 3 | ... > -- Maximum PoE allocation specified with a value in watts
-- Enable/Disable per-port power distribution
< critical | high | low > -- Enable/Disable per-port power distribution
-- Configure qinq port-type
-- Configure qinq port-type as customer-network
(p. 270)
(p. 270)
(p. 279)
(p. 244)
(p. 238)
(p. 252)
(p. 248)
(p. 219)
(p. 251)
-- Mirror destination name.
< 1 to 4 > -- Mirror destination number.
(p. 254)
(p. 261)
(p. 263)
(p. 228)
(p. 230)
(p. 233)
(p. 235)
(p. 246)
(p. 214)
(p. 282)
(p. 252)
(p. 251)
(p. 254)
(p. 256)
(p. 263)
(p. 261)
(p. 260)
(p. 261)
(p. 263)
(p. 268)
(p. 229)
interface
(p.
(p. 248)
(p. 240)
(p. 276)
(p. 250)
(p.
(p. 260)
(p. 265)
205