Parameters: 40-** Special Settings; Parameters: 42-** Safety Functions; Parameters: 43-** Unit Readouts - Danfoss VLT AutomationDrive FC 301 Programming Manual

Parameter Descriptions

3.27 Parameters: 40-** Special Settings

3.27.1 40-5* Advanced Control Settings
Parameters for configuring the advanced motor control
settings.
40-50 Flux Sensorless Model Shift
Use this parameter to enable or disable the shifting between flux
model 1 and flux model 2 at low speed. See also
parameter 1-66 Min. Current at Low Speed.
Option:
[0] Off
[1] On

3.28 Parameters: 42-** Safety Functions

The parameters in this parameter group are available when
a safety option is installed in the frequency converter. For
information about the safety-related parameters, see the
operating instructions for the safety options:
•
®
VLT Safety Option MCB 150/151 Operating
Instructions.
•
®
VLT Safety Option MCB 152 Operating Instructions.

3.29 Parameters: 43-** Unit Readouts

The parameters in this group provide readouts for
monitoring the operation of frequency converters in the
D–F enclosure sizes.
3.29.1 43-0* Component Status
This parameter group contains read-only information on
hardware components in the power section. All parameters
in this group are arrays:
•
[0]: Power card 1 (the master power card in a
parallel frequency converter, or the only power
card in a frequency converter with a single
inverter section).
•
[1]: Power card 2 (inverter connection in a parallel
frequency converter).
•
[2]: Power card 3 (inverter connection in a parallel
frequency converter).
•
[3]: Power card 4 (inverter connection in a parallel
frequency converter).
•
[4]: Power card 5 (rectifier connection in a parallel
frequency converter).
•
[5]: Power card 6 (rectifier connection in a parallel
frequency converter).
•
[6]: Power card 7 (rectifier connection in a parallel
frequency converter).
•
[7]: Power card 8 (rectifier connection in a parallel
frequency converter).
MG33MO02
Programming Guide
43-00 Component Temp.
Range:
0 °C
Function:
43-01 Auxiliary Temp.
Range:
0 °C
43-02 Component SW ID
Range:
0
*
3.29.2 43-1* Power Card Status
This parameter group contains read-only information on
the power card status. All parameters in this group are
arrays:
Danfoss A/S © 01/2018 All rights reserved.
•
[8]: Inrush card (optional).
•
[9]: Fan power card 1 (optional).
•
[10]: Fan power card 2 (optional).
Function:
NOTICE
[-128 -
*
127 °C]
This parameter is valid for FC 302 only.
Shows the temperature of a system component.
The elements of the array reference local PCB
temperature sensor measurements.
Parameter 16-31 System Temp. uses all elements
in this array to calculate the system
temperature.
Function:
NOTICE
[-128 -
*
127 °C]
This parameter is valid for FC 302 only.
Shows the temperature of an auxiliary
component. The elements of the array
reference the temperature measurements from
the NTC temperature sensors connected to
hardware components in the frequency
converter. Refer to the operating guide for
specifications of temperature sensor placement.
Function:
[0 - 20] Shows the software version of the installed option.
•
[0]: Power card 1 (the master power card in a
parallel frequency converter, or the only power
card in a frequency converter with a single
inverter section).
•
[1]: Power card 2 (inverter connection in a parallel
frequency converter).
•
[2]: Power card 3 (inverter connection in a parallel
frequency converter).
•
[3]: Power card 4 (inverter connection in a parallel
frequency converter).
•
[4]: Power card 5 (rectifier connection in a parallel
frequency converter).
3 3
219