Danfoss VLT AutomationDrive FC 301 Programming Manual page 269

Parameter Lists
8-90 Bus Jog 1 Speed
8-91 Bus Jog 2 Speed
5.3.10 9-** PROFIdrive
Par- Parameter description
ameter #
9-00 Setpoint
9-07 Actual Value
9-15 PCD Write Configuration
9-16 PCD Read Configuration
9-18 Node Address
9-19 Drive Unit System Number
9-22 Telegram Selection
9-23 Parameters for Signals
9-27 Parameter Edit
9-28 Process Control
9-44 Fault Message Counter
9-45 Fault Code
9-47 Fault Number
9-52 Fault Situation Counter
9-53 Profibus Warning Word
9-63 Actual Baud Rate
9-64 Device Identification
9-65 Profile Number
9-67 Control Word 1
9-68 Status Word 1
9-70 Edit Set-up
9-71 Profibus Save Data Values
9-72 ProfibusDriveReset
9-75 DO Identification
9-80 Defined Parameters (1)
9-81 Defined Parameters (2)
9-82 Defined Parameters (3)
9-83 Defined Parameters (4)
9-84 Defined Parameters (5)
9-85 Defined Parameters (6)
9-90 Changed Parameters (1)
9-91 Changed Parameters (2)
9-92 Changed Parameters (3)
9-93 Changed Parameters (4)
9-94 Changed Parameters (5)
9-99 Profibus Revision Counter
5.3.11 10-** CAN Fieldbus
Par- Parameter description
ameter #
10-0* Common Settings
10-00 CAN Protocol
10-01 Baud Rate Select
MG33MO02
Programming Guide
100 RPM
ExpressionLimit
Default value
0 N/A
0 N/A
ExpressionLimit
ExpressionLimit
126 N/A
1034 N/A
[100] None
0
[1] Enabled
[1] Enable cyclic master
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
[255] No baudrate found
0 N/A
0 N/A
0 N/A
0 N/A
[1] Set-up 1
[0] Off
[0] No action
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
Default value
ExpressionLimit
ExpressionLimit
Danfoss A/S © 01/2018 All rights reserved.
All set-ups TRUE
All set-ups TRUE
4 set-up FC 302 Change
only during
operation
All set-ups TRUE
All set-ups FALSE
1 set-up TRUE
2 set-ups TRUE
1 set-up TRUE
All set-ups TRUE
1 set-up TRUE
All set-ups TRUE
2 set-ups FALSE
2 set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
1 set-up FALSE
All set-ups TRUE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups TRUE
4 set-up FC 302 Change
only during
operation
2 set-ups FALSE
2 set-ups TRUE
67 Uint16
67 Uint16
Conversi Type
on index
0 Uint16
0 Uint16
- Uint16
5 5
- Uint16
0 Uint8
0 Uint16
- Uint8
- Uint16
- Uint16
- Uint8
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 V2
- Uint8
0 Uint16
OctSt
0 r[2]
0 V2
0 V2
- Uint8
- Uint8
- Uint8
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 Uint16
Conversi Type
on index
- Uint8
- Uint8
267