Danfoss VLT AutomationDrive FC 301 Programming Manual page 260

Parameter Lists
1-24 Motor Current
1-25 Motor Nominal Speed
1-26 Motor Cont. Rated Torque
1-29 Automatic Motor Adaptation (AMA)
1-3* Adv. Motor Data
1-30 Stator Resistance (Rs)
1-31 Rotor Resistance (Rr)
1-33 Stator Leakage Reactance (X1)
1-34 Rotor Leakage Reactance (X2)
1-35 Main Reactance (Xh)
1-36 Iron Loss Resistance (Rfe)
5 5
1-37 d-axis Inductance (Ld)
1-38 q-axis Inductance (Lq)
1-39 Motor Poles
1-40 Back EMF at 1000 RPM
1-41 Motor Angle Offset
1-44 d-axis Inductance Sat. (LdSat)
1-45 q-axis Inductance Sat. (LqSat)
1-46 Position Detection Gain
1-47 Torque Calibration
1-48 d-axis Inductance Sat. Point
1-49 q-axis Inductance Sat. Point
1-5* Load Indep. Setting
1-50 Motor Magnetisation at Zero Speed
1-51 Min Speed Normal Magnetising [RPM]
1-52 Min Speed Normal Magnetising [Hz]
1-53 Model Shift Frequency
1-54 Voltage reduction in fieldweakening
1-55 U/f Characteristic - U
1-56 U/f Characteristic - F
1-57 Torque Estimation Time Constant
1-58 Flying Start Test Pulses Current
1-59 Flying Start Test Pulses Frequency
1-6* Load Depen. Setting
1-60 Low Speed Load Compensation
1-61 High Speed Load Compensation
1-62 Slip Compensation
1-63 Slip Compensation Time Constant
1-64 Resonance Damping
1-65 Resonance Damping Time Constant
1-66 Min. Current at Low Speed
1-67 Load Type
1-68 Motor Inertia
1-69 System Inertia
1-7* Start Adjustments
1-70 PM Start Mode
1-71 Start Delay
1-72 Start Function
1-73 Flying Start
1-74 Start Speed [RPM]
1-75 Start Speed [Hz]
1-76 Start Current
1-8* Stop Adjustments
1-80 Function at Stop
258
®
VLT AutomationDrive FC 301/302
ExpressionLimit
ExpressionLimit
ExpressionLimit
[0] Off
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
0 N/A
ExpressionLimit
ExpressionLimit
100 %
ExpressionLimit
ExpressionLimit
35 %
100 %
ExpressionLimit
ExpressionLimit
ExpressionLimit
0 V
ExpressionLimit
ExpressionLimit
150 ms
ExpressionLimit
ExpressionLimit
100 %
100 %
ExpressionLimit
ExpressionLimit
ExpressionLimit
5 ms
ExpressionLimit
ExpressionLimit
0 kgm²
ExpressionLimit
[0] Rotor Detection
0 s
[2] Coast/delay time
ExpressionLimit
ExpressionLimit
ExpressionLimit
0 A
[0] Coast
Danfoss A/S © 01/2018 All rights reserved.
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups x FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups x FALSE
All set-ups TRUE
All set-ups FALSE
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups x FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups x FALSE
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups FALSE
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups x TRUE
All set-ups x TRUE
All set-ups x TRUE
All set-ups x TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
-2 Uint32
67 Uint16
-1 Uint32
- Uint8
-4 Uint32
-4 Uint32
-4 Uint32
-4 Uint32
-4 Uint32
-3 Uint32
-4 Int32
-6 Int32
0 Uint8
0 Uint16
0 Int16
-6 Int32
-6 Int32
0 Uint16
- Uint8
0 Int16
0 Uint16
0 Uint16
67 Uint16
-1 Uint16
-1 Uint16
0 Uint8
-1 Uint16
-1 Uint16
-3 Uint16
0 Uint16
0 Uint16
0 Int16
0 Int16
0 Int16
-2 Uint16
0 Uint16
-3 Uint8
0 Uint32
- Uint8
-4 Uint32
-4 Uint32
- Uint8
-1 Uint8
- Uint8
- Uint8
67 Uint16
-1 Uint16
-2 Uint32
- Uint8
MG33MO02