Danfoss VLT AutomationDrive FC 301 Programming Manual page 233

Parameter Lists
1-97 Thermistor Threshold level
1-98 ATEX ETR interpol. points freq.
1-99 ATEX ETR interpol points current
5.2.3 2-** Brakes
Para Parameter description
mete
r
num
ber
2-0* DC-Brake
2-00 DC Hold Current
2-01 DC Brake Current
2-02 DC Braking Time
2-03 DC Brake Cut In Speed [RPM]
2-04 DC Brake Cut In Speed [Hz]
2-05 Maximum Reference
2-06 Parking Current
2-07 Parking Time
2-1* Brake Energy Funct.
2-10 Brake Function
2-11 Brake Resistor (ohm)
2-12 Brake Power Limit (kW)
2-13 Brake Power Monitoring
2-15 Brake Check
2-16 AC brake Max. Current
2-17 Over-voltage Control
2-18 Brake Check Condition
2-19 Over-voltage Gain
2-2* Mechanical Brake
2-20 Release Brake Current
2-21 Activate Brake Speed [RPM]
2-22 Activate Brake Speed [Hz]
2-23 Activate Brake Delay
2-24 Stop Delay
2-25 Brake Release Time
2-26 Torque Ref
2-27 Torque Ramp Up Time
2-28 Gain Boost Factor
2-29 Torque Ramp Down Time
2-3* Adv. Mech Brake
2-30 Position P Start Proportional Gain
2-31 Speed PID Start Proportional Gain
2-32 Speed PID Start Integral Time
2-33 Speed PID Start Lowpass Filter Time
5.2.4 3-** Reference / Ramps
Para Parameter description
mete
r
num
ber
MG33MO02
Programming Guide
80 °C 1 set-up
ExpressionLimit 1 set-up
ExpressionLimit 2 set-ups
Default value 4 set-up
50 % All set-ups
50 % All set-ups
10 s All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
MaxReference (P303) All set-ups
50 % All set-ups
3 s All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
[0] Off All set-ups
[0] Off All set-ups
100 % All set-ups
[0] Disabled All set-ups
[0] At Power Up All set-ups
100 % All set-ups
ImaxVLT (P1637) All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
0 s All set-ups
0 s All set-ups
0.20 s All set-ups
0 % All set-ups
0.2 s All set-ups
1 N/A All set-ups
0 s All set-ups
0.0000 N/A All set-ups
0.0150 N/A All set-ups
200.0 ms All set-ups
10.0 ms All set-ups
Default value 4 set-up
Danfoss A/S © 01/2018 All rights reserved.
TRUE 100
x TRUE -1
x TRUE 0
FC 302 only Change Conversio
during n index
operation
TRUE 0
TRUE 0
TRUE -1
TRUE 67
TRUE -1
TRUE -3
TRUE 0
TRUE -1
TRUE -
TRUE 0
TRUE 0
TRUE -
TRUE -
TRUE -1
TRUE -
TRUE -
TRUE 0
TRUE -2
TRUE 67
TRUE -1
TRUE -1
TRUE -1
TRUE -2
TRUE -2
TRUE -1
TRUE -2
TRUE -1
TRUE -4
TRUE -4
TRUE -4
TRUE -4
FC 302 only Change Conversio
during n index
operation
Int16
Uint16
Uint16
Type
5 5
Uint8
Uint16
Uint16
Uint16
Uint16
Int32
Uint16
Uint16
Uint8
Uint16
Uint32
Uint8
Uint8
Uint32
Uint8
Uint8
Uint16
Uint32
Uint16
Uint16
Uint8
Uint8
Uint16
Int16
Uint8
Uint16
Uint8
Uint32
Uint32
Uint32
Uint16
Type
231