Danfoss VLT AutomationDrive FC 301 Programming Manual page 35

Parameter Descriptions
0-70 Date and Time
Range: Function:
Size [ 0 - 0 ] Sets the date and time of the internal
related clock. The format to be used is set in
*
parameter 0-71 Date Format and
parameter 0-72 Time Format.
0-73 Time Zone Offset
Range: Function:
0 min [-780 - 780 Enter the time zone offset relative to
*
min] UTC. This parameter is required for the
automatic daylight saving time
adjustment.
0-74 DST/Summertime
Option: Function:
Select how to handle daylight saving time/
summertime. For manual setting of DST/
summertime, enter the start date and end date in
parameter 0-76 DST/Summertime Start and
parameter 0-77 DST/Summertime End.
[0] Off
*
[2] Manual
0-76 DST/Summertime Start
Range: Function:
Size [ 0 - 0 ] Sets the date and time when DST/
related summertime starts. The date is
*
programmed in the format selected in
parameter 0-71 Date Format.
0-77 DST/Summertime End
Range: Function:
Size [ 0 - 0 ] Sets the date and time when DST/
related summertime ends. The date is
*
programmed in the format selected in
parameter 0-71 Date Format.
0-79 Clock Fault
Option: Function:
Enables or disables the clock warning when the
clock has not been set, or has been reset due to a
power-down and no back-up is installed. If VLT
Analog I/O Option MCB 109 is installed, [1] Enabled
is default.
[0] Disabled
[1] Enabled
MG33MO02
Programming Guide
0-81 Working Days
Array [7]
Array with 7 elements [0]–[6] shown below the parameter
number in the display. Press [OK] and step between elements
▲
with [
Option: Function:
[0] No
[1] Yes
0-82 Additional Working Days
Array [5]
Array with 5 elements [0]–[4] shown below the parameter
number in the display. Press [OK] and step between elements
▲
with [
Range:
Size related
0-83 Additional Non-Working Days
Array [15]
Array with 15 elements [0]–[14] shown below the parameter
number in the display. Press [OK] and step between elements
▲
with [
Range:
Size related
0-84 Time for Fieldbus
Range:
0 [0 - 4294967295]
*
0-85 Summer Time Start for Fieldbus
Range:
0 [0 - 4294967295] Shows the summer time start for fieldbus.
*
®
0-86 Summer Time End for Fieldbus
Range:
0 [0 - 4294967295] Shows the summer time end for fieldbus.
*
0-89 Date and Time Readout
Range:
0 [0 - 25 ] Shows the current date and time. The date and
*
Danfoss A/S © 01/2018 All rights reserved.
▼
] and [ ].
Set for each weekday if it is a working day or a non-
working day. First element of the array is Monday. The
working days are used for timed actions.
▼
] and [ ].
Function:
[ 0 - 0 ] Defines dates for additional working days
*
that would normally be non-working
days according to parameter 0-81 Working
Days.
▼
] and [ ].
Function:
[ 0 - 0 ] Defines dates for additional working days
*
that would normally be non-working
days according to parameter 0-81 Working
Days.
Function:
Shows the time for fieldbus.
Function:
Function:
Function:
time is updated continuously.
The clock does not begin counting until a setting
different from default has been made in
parameter 0-70 Date and Time.
3 3
33