Danfoss VLT AutomationDrive FC 301 Programming Manual page 193

Parameter Descriptions
16-83 Fieldbus REF 2
Range:
16-84 Comm. Option STW
Range: Function:
0 [0 - 65535 ] Show the status word of the extended fieldbus
*
communication option.
For more information, refer to the relevant
fieldbus manual.
16-85 FC Port CTW 1
Range: Function:
0 [0 - View the 2-byte control word (CTW) received
*
65535 ] from the fieldbus master. Interpretation of the
control word depends on the fieldbus option
installed and the control word profile selected
in parameter 8-10 Control Profile.
16-86 FC Port REF 1
Range: Function:
0 [-200 - View the 2-byte status word (STW) sent to the
*
200 ] fieldbus master. Interpretation of the status word
depends on the fieldbus option installed and the
control word profile selected in
parameter 8-10 Control Profile.
16-87 Bus Readout Alarm/Warning
Range: Function:
0 [0 - 65535] Alarm and warning numbers in hex as shown in
*
the alarm log. The high byte contains the alarm,
the low byte contains the warning. The alarm
number is the 1st one that occurred after the
last reset.
16-89 Configurable Alarm/Warning Word
Range: Function:
0 [0 - 65535] This alarm/warning word is configured in
*
parameter 8-17 Configurable Alarm and
Warningword to match the actual requirements.
3.16.7 16-9* Diagnosis Readouts
NOTICE
When using MCT 10 Set-up Software, the readout
parameters can only be read online, that is as the actual
status. This means that the status is not stored in the
MCT 10 Set-up Software file.
MG33MO02
Programming Guide
Function:
fieldbus which is used by the
frequency converter. The value
is in position units defined in
parameter group 17-7* Position
Scaling.
Danfoss A/S © 01/2018 All rights reserved.
16-90 Alarm Word
Range: Function:
0 [0 - 4294967295 ] Show the alarm word sent via the serial
*
communication port in hex code.
16-91 Alarm Word 2
Range:
0 N/A [0 - 4294967295 N/A] View the alarm word sent via the
*
16-92 Warning Word
Range: Function:
0 [0 - 4294967295 ] Show the warning word sent via the
*
serial communication port in hex code.
16-93 Warning Word 2
Range:
0 N/A [0 - 4294967295 N/A] View the warning word sent via
*
16-94 Ext. Status Word
Range:
0 N/A [0 - 4294967295 N/A] Returns the extended warning
*
16-96 Maintenance Word
Range: Function:
0 [0 - Readout of the preventive maintenance word.
*
4294967295 ] The bits reflect the status for the
programmed preventive maintenance events
in parameter group 23-1* Maintenance. 13 bits
show combinations of all the possible items:
•
Bit 0: Motor bearings.
•
Bit 1: Pump bearings.
•
Bit 2: Fan bearings.
•
Bit 3: Valve.
•
Bit 4: Pressure transmitter.
•
Bit 5: Flow transmitter.
•
Bit 6: Temperature transmitter.
•
Bit 7: Pump seals.
•
Bit 8: Fan belt.
•
Bit 9: Filter.
•
Bit 10: Frequency converter cooling
fan.
•
Bit 11: Frequency converter system
health check.
•
Bit 12: Warranty.
Function:
serial communication port in hex
code.
Function:
the serial communication port in
hex code.
Function:
word sent via the serial
communication port in hex code.
191
3 3