Danfoss VLT AutomationDrive FC 301 Programming Manual page 154

Parameter Descriptions
13-16 RS-FF Operand R
Option:
[41] Reset Trip
[42] Auto-reset Trip
[43] Ok key
3 3
[44] Reset key
[45] Left key
[46] Right key
[47] Up key
[48] Down key
[50] Comparator 4
[51] Comparator 5
[60] Logic rule 4
[61] Logic rule 5
[70] SL Time-out 3
[71] SL Time-out 4
[72] SL Time-out 5
[73] SL Time-out 6
[74] SL Time-out 7
[75] Start command given
[76] Digital input x30/2
[77] Digital input x30/3
[78] Digital input x30/4
[79] Digital input x46/1
[80] Digital input x46/3
[81] Digital input x46/5
[82] Digital input x46/7
[83] Digital input x46/9
[84] Digital input x46/11
[85] Digital input x46/13
[90] ATEX ETR cur.
warning
[91] ATEX ETR cur. alarm
[92] ATEX ETR freq.
warning
[93] ATEX ETR freq. alarm
[94] RS Flipflop 0
[95] RS Flipflop 1
[96] RS Flipflop 2
[97] RS Flipflop 3
[98] RS Flipflop 4
[99] RS Flipflop 5
[100] RS Flipflop 6
[101] RS Flipflop 7
[102] Relay 1
[103] Relay 2
152
®
VLT AutomationDrive FC 301/302
Function:
[OK] is pressed. Only available on
the graphical LCP.
[Reset] is pressed. Only available on
the graphical LCP.
[◄] is pressed. Only available on the
graphical LCP.
[►] is pressed. Only available on the
graphical LCP.
▲
[ ] is pressed. Only available on
the graphical LCP.
▼
[ ] is pressed. Only available on
the graphical LCP.
Danfoss A/S © 01/2018 All rights reserved.
13-16 RS-FF Operand R
Option: Function:
[104] Relay 3
X47/VLT
113.
[105] Relay 4
X47/VLT
113.
[106] Relay 5
X47/VLT
113.
[107] Relay 6
X47/VLT
113.
[108] Relay 7
X34/VLT
[109] Relay 8
X34/VLT
[110] Relay 9
X34/VLT
NOTICE
[222] Homing Ok
This option is available only
with software version 48.20
and newer.
Homing is completed with the
selected homing function
(parameter 17-80 Homing Function).
NOTICE
[223] On Target
This option is available only
with software version 48.20
and newer.
Positioning is completed and the
on-target signal is sent when the
actual position is within
parameter 3-05 On Reference
Window for the duration of
parameter 3-09 On Target Time and
the actual speed does not exceed
parameter 3-05 On Reference
Window.
NOTICE
[224] Position Error
This option is available only
with software version 48.20
and newer.
The position error exceeds the
value in parameter 4-71 Maximum
Position Error for the time set in
parameter 4-72 Position Error
Timeout.
®
Extended Relay Card MCB
®
Extended Relay Card MCB
®
Extended Relay Card MCB
®
Extended Relay Card MCB
®
Relay Card MCB 105.
®
Relay Card MCB 105.
®
Relay Card MCB 105.
MG33MO02