Daihatsu F300 Service Manual page 1074

•
•
•
•
APPENDIX
TIGHTENING TORQUE TABLE FOR GENERAL STANDARD BOLTS & NUTS
NOTE:
The table below indicates the tightening torques for those standard bolts and nuts which are not posted
in the tightening torque table.
Nominal
Standard tightening torque
Pitch
Category diameter
mm
Target value
Tightening range
mm
N·m kgf-m fl-lb N·m kgf-m
ft-lb
6 1.0
5.39 0.55 3.98 4.31 - 6.47
0.44-0.66
3.18-4.77
[5.66] [0.60]
[4.34] [4.71 - 7.06] [0.48- 0.72] [3.47- 5.21]
4T
12.75 1.30 9.40 10.2- 15.3 1.04-1.56 7.52- 11.28
(Bolt having a mark of
8 1.25
[14.22] [1.45] [10.49] [11.3& 17.06] [1.16- 1.74] [8.39- 12.59]
• 4"
at
its head section)
Example of part number
10 1.25
25.50 2.6 18.81 20.4- 30.6 2.08-3.12 15.04- 22.57
(91CXJ()- 4CXJ())
[28.44] [2.90] [20.98] [22.75-34.13]
[2.32 - 3.48]
[16.78-25.17]
12 1.25
47.07 4.8
34.72 37.66 - 56.49 3.84-5.76 27.77-41.66
[52.96] [5.4] [39.06] (42.36- 63.55]
[4.32- 6.48]
[31.25- 46.87]
6
1.0
6.37
0.65
4.70 5.1-7.65 0.52-0.78 3.76-5.64
[7.35] [0.75] [5.42] [5.66 - 8.83] [0.6- 0.9]
[4.34- 6.51]
5T
15.69 1.60 11.57 12.55-18.83
1.28-1.92
9.26- 13.69
(Bolt having a mark of
8 1.25
[17.16] [1.75] [12.66] [13.73- 164.66]
[1.40-2.10)
(":0.13-15.19]
·s· at its head section)
Example of part number
32.36 3.3 23.87
25.89 - 38.83
2.64-3.96
19.1 - 28.64
(91CXJ() - SCXJ())
10 1.25
[35.30] [3.6] [26.04] [28.24 - 42.36] [2.88 - 4.32] [20.83- 31.25]
12
1.25
58.64 6.0 43.4 47.07 - 70.61
4.80-7.20
34.72- 52.08
[65.70] [6.7] [48.46] [52.56 - 78.65] [5.36 - 8.04] [38.77-58.15]
6 1.0
7.65 0.8 5.79
6.28- 9.41
0.64-0.96 4.63-6.94
[8.83] [0.9]
[6.51] [7.06 -10.59] [0. 72 - 1.08] [5.21- 7.81]
6T
19.12 1.95
14.10
15.3-22.95 1.56 -2.34 11.28-16.93
(Bolt having a mark of
8 1.25
[20.59] [2.10] [15.19] [16.48- 24.71]
[1.68 - 2.52]
[12.15 -18.23]
"6" at its head section)
Example of part number
39.23 4.00
28.93 31.38- 47.07
3.20-4.80
23.15 - 34.72
(91CXJ()- SCXJ())
10 1.25
[43.15] [4.40] [31.83] [34.52 -51. 76]
[3.52 - 5.28]
[25.46- 38.19]
12
1.25
71.59 7.30 52.80
57.27- 85.91
5.84-8.76 42.24 - 63.36
[79.43] [8.10] [58.59] [63.55 - 95.32] [6.48 - 9.72] [46.87 - 70.30]
6 1.0
10.79
1.10 7.96
8.63- 12.94 0.88- 1.32
6.37-9.55
[11.76] [1.20] [8.68] [9.41 ·14.12] [0.96 -1.44] [6.94- 10.42]
7T
25.5 2.60 18.81 20.4. 30.6 2.08- 3.12
15.04- 22.57
(Bolt having a mark of
8 1.25
[28.44]
[2.90] [20.98] [22.75-34.13] [2.32 - 3.48] [16.78-25.17]
"7" at its head section)
Example of part number
51.98 5.30 38.33
41.58 - 62.37
4.24. 6.36
30.67 - 47.95
(91CXJ0- 7CXJ())
10 1.25
[57.86] [5.90] [42.67] [46.29- 69.43] [4.72. 7.08]
[34.14- 51.21]
12 12.5
95.12 9.70 70.16 76.1-114.15 7.76- 11.64 56.13-84.19
[109.97] [10.50] [75.94] [82.38- 123.56]
[8.40- 12.60] [60.76- 91.14]
PTB/1 *0.9071 16.67 1.7 12.3 11.76-21.57 1.2-2.2 8.67- 15.91
Pipe tapered thread
PT1/4
*1.3368 24.52
2.5 18.08 19.61 - 29.42 2.0-3.0 14.46-21.67
PT3/8
*1.3368
29.42 3.0 21.7 24.52 - 34.32 2.5- 3.5 18.08- 25.32
PT1/2 *1.8143 29.42 3.0 21.7 24.52 - 34.42
2.5 ·3.5 18.08 - 25.32
Numerals in [ ] denote those for flange bolts.
The asterisked mark (*) represents pitch conversion value.
WFE9().J(l13
A-11 ~