Daihatsu F300 Service Manual page 1055

HARNESS & WIRING DIAGRAM
•
Section: Apron (right side) Application: All vehicles
Hamess leading to side
Up
D
tum
signal lam\ B
,,--1
Check
connector
(g\etl)
Bo~y
ground
(EFI-LHD)
~
·l~k
~
Headlamp RH..,.
©
4~ ~
c
v~nginewlre
Front tum s1gnai.
.t:?'
~
(LHD. EFI vehicle only) Dashboard
""
Eng•ne
V ""
'----
~'M'"re
t,,,,,..,,
No.2 Wlre
p,
1--®
®
A
9
[As VIewed from top]
Dommy
Harness leading to 3-stage actuator
Fig_ 1
connector
No. Operation procedure
Soc-
Control item
'"""""'
tion
1. Except for the 3-stage specifications, assemble the
A
Ensure that the harness
is
clamped to the
To prevent abnormal
•
dummy connector and secure it to the apron bracket. bracket securely . noise and interference
2. Tighten the body ground branch wire in such a way that 8 Ensure that the branch line faces For better appearance
it
faces downward.
downward.
3.
Secure the ClamP
to
the dashboard bracket with the
c
Ensure that the harness is clamped To prevent the horness
bolt
securely at a point lower than the from interfering With
tightening point.
the brake tube, etc.
4.
Insert
the
check connector to the dashboard bracket.
D
Ensure that the lock is made positively. To prevent connector
until the lock is engaged.
from being removed
EFI - 6-oole. green
and
interfered
Rear-ASS 6- pole. gray
5.
After completion of check connector wiring, clamp the
E
Ensure that the harness is clamped To assure route and to
harness with the apron cowl wire.
(Use another band clamp for the U.S. specifications.)
securely to the apron side.
prevent interference
6. When nstalling the clamp to the dashboard-side F Ensure that
the
clamp is assembled within To prevent the ha"ness
bracket, ensure that the clamp is not protruded from the
the bracket width.
from
interfering
with
ctamp width ({). Never bend the clamp downward.
the brake tube
(Rg. 1)
Section: Apron (left side) Application: All vehicles
•
C Washer \nk Headip cleaner tank Up
Body groun'd
~
L
Fr
-?,~\(~
'"""m"gM"=o-----~~
1
~"'""mpLH
~
-:::------.._
C:~ ~
'""'"m .,,., •mo
D I
~J,"'~"
Hom
'
.
Hamesslead•ng to
Hamess lead•ng to
3-stage actuator
ASS actuator (RHO)
Dummy connector
No. Operation procedure
Soc-
Control item
Pu•poses
tion
1. Except for the 3-stage specifications, assemble the
A
Ensure
that
the harness is clamped
to
the
To prevent abnormal
dummy connector and secure it to the apron bracket.
braCket securely.
noise and interference
2.
Clamp the apron securely.
8 Ensure that the clamping is made securely. To prevent the harness
from being caught-in
under the waSher tank
and cleaner·tank
3.
Tighten the body ground branch wire in such a way that
c
Ensure that the branch line faces For better appearance
it faces downward.
oownwarn.
4 .
Route the harness located below the washer tank along
D Ensure that the harness is not caught-in To prevent the harness
the
inside of
the
vehicle so that the harness may
not
be
between the washer tank and the body.
from being caught-in
caught-in under the tank.
under the washer tank
•
HW-45