Daihatsu F300 Service Manual page 1060

~H~A~RN~E=S~S~&~W~I~RI~N~G~D~I~A~G~RA~M~-------------------------------- 1 --
Section: Harness leading to tum signal lamp switCh Application:
$tearing
i'>QSI
Tum signal
lamp switch
sw
All vehicles
:f\
~~'A
-~
'
Edge protector Instrument panel ·-- E
retainer dge protectof
I
L.H.D. veh,cle
I I
R.H.D. vehicle
I
Operation procedure
Sec-
Control
item Purposes
tt
~-"~~====~~~~c=~~~~~==~-+~'~'.'Cf~c=~=-~=====c~~=co--1~c=~~~----~
1. After connecting the tum signal lamp switch connector. Ensure that the connector is secured to To prevent the
2.
3
secure it to
the
bracket of
the
instrument
pa-1el
retainer.
the
bracket
positively.
connector from
interlering With the
retainer flange
Positively clamp the lead wire at the tum signal lamp
switch side
by
means of the steertng
post
clamp.
Route the hamess leading to the ignition switch in front
of the turn signal lamp switch lead wire.
B
c
Ensure that the clamp is secured
positively.
l;m;ure that the harness leading
to
the
ignition switch is routed in front of the tum
signal lamp switch wire.
To prevent the lead
wire from interfering
with the retainer Hange
To prevent the harness
from interfering with
the retainer flange
Section: Related to right cowl side Application: All vehicles
1.
2.
3.
4.
""
Fr
__J
Harness 1eadir1g Harness leadir1g
to back side of
~
.
~to
back side of
•nstn.mel'll panel mstrument panel
~ O
Cowl
side trim
{1
c
4
AS
viewed
from
top
A
RH
,,__/
Operation
procedure
L.H.D.
vehicle: Route the branch
r.ne of
the
harness
leading
to
the door between the dash
panel
attaching
bracket of the EFI ECU and the dash panel.
l.H. .
vehicle:
When
tightening the
ECU
attaching
bracket.
be
careful not
to
allow the harness
to
be
caught-in.
A.H. . vehicle: Ensure that the branch tine of
the
hamess leading to the door is not protruded
from
the
edge surface of the relay block
toward
the interior side.
Place the connector connected with the door wire
between the upper trim of the trim clip
and
the
cowl
side. --·
Sec-
'""
A
B
c
RH
,,__/
Control item
Ensure
tha!
the branch Jines of the
harnesses leading to the door and leading
to the ASB ECU are placed between the
ECU
bracket
and
the dash panel.
Ensure
that the harness
is
not caught-in by the
attaching bOlt
and bracket.
Ensure
thai !he
blanc:h lines ollhe
namesses no
to
lhe OOOr and leading
to
the ASS ECU
are
placecl a1
the
inside
of
tile edge
surtace
of lhe relay block. Also,
ensure
lhalltle bJancil
tines run
along lhe cowl side.
Ensure that the connector is placed
between1tle upper trim
of the trim cr1p and
the cowl side.
HW-50
To assure the route
To assure the
fl.lnction
To prevent the harness
from interfering with
the accelerator
pedal
To
assure
the
route
To prevent the trim
from floating
•
•