Controller Set-Up - Goldacres G6 Crop Cruiser 2 Series Operator's Manual

AIXR APPLICATION CHART
CAPACITY
DROP LERAP
ONE NOZZLE
SIZE RATINGS
5 6
bar
IN L/MIN
km/h km/h
XC
1.0 — 0.34 81.6 68.0
2.0 C — 0.48 115 96.0
AIXR110015 3.0 C — 0.59 142 118
4.0 M — 0.68 163 136
(100)
5.0 M — 0.76 182 152
6.0 — 0.83 199 166
M
1.0 XC — 0.46 110 92.0
2.0 VC — 0.65 156 130
AIXR11002
3.0 C — 0.79 190 158
4.0 M — 0.91 218 182
(50)
5.0 M — 1.02 245 204
6.0 M — 1.12 269 224
1.0 XC ** 0.57 137 114
2.0 VC ** 0.81 194 162
AIXR110025
3.0 VC ** 0.99 238 198
4.0 C ** 1.14 274 228
(50)
5.0 C ** 1.28 307 256
6.0 M — 1.40 336 280
1.0 XC ** 0.68 163 136
The 3TS Pro option requires three nozzles to be selected giving the operator a greater
2.0 VC ** 0.96 230 192
AIXR11003 range of application rates and travel speeds.
3.0 VC ** 1.18 283 236
4.0 C ** 1.36 326 272
(50)
Example: Nozzle Selection for the 3TS Pro Option 5.0 C ** 1.52 365 304
6.0 M — 1.67 401 334
1.0 UC *** 0.91 218 182
Using the AIXR Teejet Application Chart:
2.0 XC ** 1.29 310 258
AIXR11004
3.0 VC ** 1.58 379 316
Look down the nozzle capacity column (l/min) and select two
4.0 VC ** 1.82 437 364
(50)
5.0 C ** 2.04 490 408
nozzles to suit an output of 0.8 l/min (shown above).
6.0 C — 2.23 535 446
UC
1.0 *** 1.14 274 228
The AXIR110015 nozzle @ 2 Bar gives 0.48l/min which is 82.3
2.0 XC *** 1.61 386 322
AIXR11005
3.0 VC ** 1.97 473 394
l/ha at 7 kmh and an output of 0.68l/min @ 4 Bar which is 81.6
(50) 4.0 VC ** 2.27 545 454
5.0 C ** 2.54 610 508
l/ha at 10 kmh.
6.0 C — 2.79 670 558
1.0 UC *** 1.37 329 274
The AXIR11002 nozzle @ 2 Bar gives 0.65l/min which is 78.0 l/
2.0 XC *** 1.94 466 388
AIXR11006
3.0 VC *** 2.37 569 474
ha at 10 kmh and an output of 1.02l/min @ 5 Bar which is 76.5
4.0 VC ** 2.74 658 548
(50)
l/ha at 16 kmh.
5.0 C ** 3.06 734 612
6.0 C — 3.35 804 670
1.0 UC — 1.82 437 364
The AXIR110025 nozzle @ 2 Bar gives 0.81l/min which is 81.0
2.0 XC — 2.58 619 516
l/ha at 12 kmh and an output of 1.28l/min @ 5 Bar which is AIXR11008 3.0 VC — 3.16 758 632
4.0 VC — 3.65 876 730
(50)
76.8 l/ha at 20 kmh.
5.0 VC — 4.08 979 816
6.0 C — 4.47 1073 894
1.0 UC — 2.28 547 456
These nozzles should allow the controller to apply 80 litres per
2.0 UC — 3.23 775 646
ha at speeds ranging from 7 up to 40 kmh
3.0 XC — 3.95 948 790
AIXR11010
4.0 VC — 4.56 1094 912
5.0 VC — 5.10 1224 1020
Fit the selected nozzle to the boom.
6.0 VC — 5.59 1342 1118
NOTE: Always double check your application rates. Tabulations are based on spraying water at 21°C.
DROPLET SIZE CATEGORIES
XF VF F M
EXTREMELY VERY FINE MEDIUM
FINE FINE
There are often very serious limitation to possible maximum spray speeds.
Droplet size may vary with nozzle capacity, spray angle and spray pressure.
Maximum spray speeds are limited by safety factors, chemicals used, maximum
boom output in l/min, type of target, field conditions, terrrain and weather
conditions.
GA8701177 REV 2 APRIL 2022
l/ha 50 cm
CAP PART
NUMBER
7 8 10 12 16 18 20
km/h km/h km/h km/h km/h km/h km/h
58.3 51.0 40.8 34.0 25.5 22.7 20.4
82.3 72.0 57.6 48.0 36.0 32.0 28.8
101 88.5 70.8 59.0 44.3 39.3 35.4
117 102 81.6 68.0 51.0 45.3 40.8
130 114 91.2 76.0 57.0 50.7 45.6
142 125 99.6 83.0 62.3 55.3 49.8
78.9 69.0 55.2 46.0 34.5 30.7 27.6
111 97.5 78.0 65.0 48.8 43.3 39.0
135 119 94.8 79.0 59.3 52.7 47.4
156 137 109 91.0 68.3 60.7 54.6
175 153 122 102 76.5 68.0 61.2
192 168 134 112 84.0 74.7 67.2
97.7 85.5 68.4 57.0 42.8 38.0 34.2
139 122 97.2 81.0 60.8 54.0 48.6
170 149 119 99.0 74.3 66.0 59.4
195 171 137 114 85.5 76.0 68.4
219 192 154 128 96.0 85.3 76.8
240 210 168 140 105 93.3 84.0
117 102 81.6 68.0 51.0 45.3 40.8
165 144 115 96.0 72.0 64.0 57.6
202 177 142 118 88.5 78.7 70.8
233 204 163 136 102 90.7 81.6
261 228 182 152 114 101 Hawkeye Option (Nozzle Control System) 91.2
286 251 200 167 125 111 100
156 137 109 91.0 68.3 60.7 54.6
The Hawkeye Pulse Width Modulated (PWM) technology is an
221 194 155 129 96.8 86.0 77.4
271 237 190 158 119 105 94.8
available option. If fitted refer to the manufacturer's manual.
312 273 218 182 137 121 109
350 306 245 204 153 136 122
382 335 268 223 167 149 134
195 171 137 114 85.5 76.0 68.4
276 242 193 161 121 107 96.6
338 296 236 197 148 131 118
389 341 272 227 170 151 136
435 381 305 254 191 169 152
478 419 335 279 209 186 167
235 206 164 137 103 91.3 82.2
333 291 233 194 146 129 116
406 356 284 237 178 158 142
470 411 329 274 206 183 164
525 459 367 306 230 204 184
574 503 402 335 251 223 201
312 273 218 182 137 121 109
442 387 310 258 194 172 155
542 474 379 316 237 211 190
626 548 438 365 274 243 219
699 612 490 408 306 272 245
766 671 536 447 335 298 268
391 342 274 228 171 152 137
554 485 388 323 242 215 194
677 593 474 395 296 263 237
782 684 547 456 342 304 274
874 765 612 510 383 340 306
958 839 671 559 419 373 335
C VC XC UC
COARSE VERY EXTREMELY ULTRA
COARSE COARSE COARSE
| 13
teejet.com
Calibration – Set & Check Application Rates
Opening Warning screen of the optional Raven CR7.

4 Controller Set-Up

New application rate values must be entered into Automatic
Control Module (RCM) according to the boom's nozzle
configuration.
The Cruiser may be fitted with one of four nozzle control option
technologies:
a) Single line boom
b) 3TS option
c) 3TS Pro option
d) Hawkeye option (nozzle control system).
a) Enter Values for the Single Line Boom
After nozzle selection, a single line boom configuration requires
the application rates to be entered into the controller according
to the nozzle selected.
To Enter New Values:
1 Start the engine.
2
"WARNING DO NOT OPERATE ON ROADWAYS OR NEAR
appears on the optional Raven CR7 screen or
OBSTACLES"
ISO bus screen.
Press the OK button and the home screen appears.
5
95