Cabin Seats - Goldacres G6 Crop Cruiser 2 Series Operator's Manual

Cabin Seats

The cabin is equipped with an Operator's seat
and a fold-up Training seat.
Operator's Seat
The Operator's Seat has its own air
compressor - operarating as soon as the
ignition is On. Adjustments are shown right.
To make adjustments:
1 Fore/Aft Adjustment Lever
First release the Fore/Aft Locking lever (2).
Then lift the Fore/Aft Adjustment lever (1) &
slide the seat back or forth to the position
desired.
Finally, lock the seat into position with the
Fore/Aft Locking lever (2).
2 Fore/Aft Locking Lever
Releasing the lever enables Seat Fore/
Aft Adjustment (1) and engaging the lever
locks the seat to its desired position.
3 Seat Height & Weight Adjustment
Weight Adjustment
The seat must be adjusted for the driver's
weight by briefly pulling the actuator lever
of the automatic weight height adjuster
with the vehicle at a standstill and the
driver sitting on the seat. The driver must
sit absolutely still during adjustment.
To avoid injury to individual operators, all
seat settings for the operator's weight &
comfort must be checked and adjusted for
each operator before driving.
Height adjustment
With ignition key On, seat height is set
pneumatically & is continuously adjustable.
Adjust seat height by pulling or pushing
the adjustment lever fully up or down.
Lift the lever to raise the seat (air is
pumped into the airbag suspension).
GA8701177 REV 2 APRIL 2022
Push the lever down to lower the seat (air
is release from the air bag.
If the adjustment reaches the top or
bottom endstop, the height is adjusted
automatically in order to guarantee a
minimum spring travel.
To avoid mechanism damage, do not
operate adjustment lever/compressor for
more than 1 minute at a time.
4 Absorber Lever
The Absorber Lever setting of the seat can
be varied to suit the on & off-road driving
conditions. The cushioning effect can be
individually adjusted for this purpose.
Turn the lever to the desired position &
release: 1- Soft 2- Medium 3- Hard.
5 Lap Seat Belt
Clip the Lap Seat Belt into postion
whenever seated in the cabin.
6 Seat Tilt Lever
Lift the Seat Tilt Lever to tilt the back of
the seat forward or rearward to suit, then
release the lever to lock it into position.
7 Armrest Height Adjustment
Both armrests can be folded up if required
& armrest height individually adjusted.
To adjust armrest height, remove the
round cap, then loosen the hexagon nut
(13 mm) and adjust the armrest to the
desired height (5 steps). Tighten the nut
(25Nm) & replace the cap into the nut.
8 Lumbar Adjustment Knob (behind seat)
By rotating the Lumbar Adjustment Knob
left or right, both the height & curvature of
the backrest cushion can be adjusted to
increase operator's seating comfort.
9 Armrest Inclination Adjustment
Each Armrest Inclination can be altered by
turning its adjustment knob.
Rotating the knob outward, lifts the front
part of the armrest. Rotating the knob
inwards, lowers the front of the armrest.
Cabin – Your Sprayer at a Glance
11
10
1
3
2
Location of the Operator Seat settings (refer to numbered information & headings on this page for instruction).
All position, weight, height & comfort adjustments must be made before driving.
10 Seat Pan Angle Adjustment
Pull the Seat Pan Angle Adjustment Lever
upwards and exert pressure on the front or
rear part of the seat pan to move the seat
pan into its desired position, then release
the lever to lock its position.
6 7 8
5
4
11 Seat Cushion Depth Adjustment
The Seat Cushion Depth can be adjusted.
To adjust the seat cushion depth, pull the
right handle upwards, then by moving the
seat cushion backwards or forwards the
desired cushion position can be reached.
Release the lever on completion.
3
9
31