Closing The Rename Data Name Popup Screen - Mitsubishi Electric M800VW Series Manual

M800V/M80V Series PLC Development Manual
6 Explanation of Built-in Editing Function (PLC On-board)
6.13 NC File Operation Menus
Abnormal operation
This information describes the details of error messages displayed on the rename data popup screen and the corrective
action thereof.
Error message
An old data name has not been inputted.
Please input an old data name.
Please input a new data name. Enter the
new data name.
This project/data name is a reserved device
name. Please choose another name.
Prohibited characters were used in the file
name.
Do not use the following characters in file
names:
/, :, ,, ;, *, ?, \, ", <, >, |
File name includes the multi-byte character
code. Please confirm file name.
Illegal characters have been used for a data
name. Use legal characters.
A file was specified which does not exist in
the NC.
The same data name has already been set.
Change to a different data name.
Data names for device comments cannot be
changed.
It cannot change into the same name as a
common device comment. Please choose
another name.
Data name cannot be changed because the
PLC is running. Execute again after the PLC
stops.
(*1) Refer to "6.6.1 PLC Data Used by the PLC On-board".

6.13.7.7 Closing the Rename Data Name Popup Screen

Use any of the following methods to close the rename data popup screen.
Methods to close the screen
Change the data name.
Press the [CLOSE] menu key.
Press the left arrow key.
Press the [ESC] key on the software keyboard.
IB-1501614-B
Error details
This is displayed when the [CHANGE] menu
key is pressed while the old data name input
field is still blank.
This is displayed when the [CHANGE] menu
key is pressed while the new data name input
field is still blank.
This is displayed after the [CHANGE] menu key
is pressed when a reserved device name (*1)
has been entered as the old data name or the
new data name.
This is displayed after the [CHANGE] menu key
is pressed and the old data name or the new
data name contains prohibited characters (*1).
This is displayed after the [CHANGE] menu key
is pressed and the old data name or the new
data name contains double-byte characters.
This is displayed after the [CHANGE] menu key
is pressed and the final character of the old
data name or the new data name is a period.
This is displayed when the [CHANGE] menu
key is pressed after specifying a data type or
data name that is not stored in the NC.
This is displayed when the [CHANGE] menu
key is pressed after specifying a new data
name that already exists.
This is displayed when the [CHANGE] menu
key is specified after a comment is specified for
the old data name.
This is displayed when the [CHANGE] menu
key is specified after a comment is specified for
the new data name.
This is displayed when trying to change data
names without stopping the PLC.
368
Remedy
Enter a valid old data name before pressing the
[CHANGE] menu key.
Enter a valid new data name before pressing
the [CHANGE] menu key.
Enter a valid old data name or new data name
before pressing the [CHANGE] menu key.
Enter a valid old data name or new data name
before pressing the [CHANGE] menu key.
Enter a valid old data name or new data name
before pressing the [CHANGE] menu key.
Enter a valid old data name or new data name
before pressing the [CHANGE] menu key.
Press the [CHANGE] menu key after specifying
a data type or data name in the data name that
is stored in the NC.
Specify a new data name that does not exist in
the NC before pressing the [CHANGE] menu
key.
Specify something other than a comment for
the old data name and press the [CHANGE]
menu key.
Specify something other than a comment for
the new data name and press the [CHANGE]
menu key.
Change data names when the PLC is not run-
ning.