Mitsubishi Electric PAC-WHS01WF-E Technician Manual
  1. Manuals
  2. Brands
  3. Mitsubishi Electric Manuals
  4. Control Systems
  5. PAC-WHS01WF-E
  6. Technician manual

Mitsubishi Electric PAC-WHS01WF-E Technician Manual

Hide thumbs Also See for PAC-WHS01WF-E:
Table of Contents

Advertisement

Quick Links

®
TECHNICIAN MANUAL
FOR INSTALLER
2.10
● This manual reflects the installation of the Wi-Fi Interface (PAC-WHS01WF-E), Wireless Interface 1
(PAC-USWHS002-WF-1), and Wireless Interface 2 (PAC-USWHS002-WF-2) for the 2.12 and 2.14
kumo cloud app release updates.
● This manual has not been updated yet to show the additions of the 2.12 and 2.14 updates, but the
manual will be updated in the near future.
Note: The changes in 2.12 and 2.14 were minor and did not change the overall way the equipment is installed.
● The Wireless Interface 1 and 2 must connect to a 2.4 GHz Wi-Fi
● The Wireless Interface 1 and 2 will not work on a 5 GHz Wi-Fi network.
○ The Wireless Interface 1 and 2 can only connect to Wi-Fi channels 1-11.
● For the best performance connect the Wireless Interface 1 and 2 to a 2.4 GHz only SSID, but there
are some multi-band Wi-Fi networks that can correctly manage a 2.4 GHz only device.
○ Please verify if your multi-band Wi-Fi router can manage 2.4 GHz only devices.
Note: The set up of the Wireless Interface to the kumo cloud app requires a Wi-Fi network with a live internet
connection.
NOTE
ATTENTION
®
network.

Advertisement

Table of Contents
loading

Related Manuals for Mitsubishi Electric PAC-WHS01WF-E

Summary of Contents for Mitsubishi Electric PAC-WHS01WF-E

  • Page 1 FOR INSTALLER 2.10 NOTE ● This manual reflects the installation of the Wi-Fi Interface (PAC-WHS01WF-E), Wireless Interface 1 (PAC-USWHS002-WF-1), and Wireless Interface 2 (PAC-USWHS002-WF-2) for the 2.12 and 2.14 kumo cloud app release updates. ● This manual has not been updated yet to show the additions of the 2.12 and 2.14 updates, but the manual will be updated in the near future.

  • Page 2: Table Of Contents

    Adjust a Setting ............................34 Firmware ..............................35 Terms and Definitions ............................35 FAQs................................36 kumo cloud on Google Home ......................... 36 kumo cloud skill with Amazon Alexa ....................... 37 Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 3: Kumo Cloud

    Mitsubishi Electric Wireless Interface to enable remote control of Mitsubishi Electric Cooling & Heating equipment from a smartphone or a tablet. The app can be used as the only controller or with compatible controllers. When a Wireless Interface 2 (WI 2) is used to connect the ®...

  • Page 4: Get Started

    Review the Terms and Conditions and tap I Agree. ® account, unless you log out by tapping Settings > My Account You will remain logged in to your kumo cloud > Log out. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 5: Install

    In a new construction, this may be a temporary network. The homeowner may switch networks later. Connect a Mitsubishi Electric Wireless Interface to the CN105 connector on each indoor unit. See the Installation/Instruction Manual and Compatibility Chart at: https://qrco.de/WI1MLD https://qrco.de/WI2MLD...

  • Page 6: Connect A New Site

    Wait until the amber LED turns on and then begins to blink (about 8 seconds), then release the button. If using first generation Wireless Interfaces (PAC-WHS01WF-E), skip to First Generation Wireless Interfaces.

  • Page 7: Create A New Site

    Step 4. Tap Connect New Site. Enter a unique Name for the job site, such as Jones House or Dr. Smith’s Office. Tap Next. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 8: Connect The Site To The Wireless Network

    Airflow according to the unit model. If this screen doesn’t appear, airflow/static pressure doesn’t apply, or must be set using dip switches as shown in the indoor unit installation manual. See Airflow for to set airflow. Static Pressure Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 9: Enable Changeover Group

    Select input field and input desired Group Name. Tap Create Group to proceed. Here, the recently created/desired Changeover Group is displayed as selected. Confirm this selection. Tap Next to continue. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 10: Define Changeover Settings

    In the kumo cloud app, tap Settings > System Setup > Installer Settings. Enter the installer login (9999). Tap the required site and then tap the zone. Select and define the required Changeover Settings as explained above. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 11: Finish Setup

    Wireless Interface and the local wireless router. If there is a Very Weak Signal or No Signal, consider relocating the Wireless Interface, relocating the router, adding a repeater, or use a Mitsubishi Electric IT Extender (PAC-WHS01IE-E). The Wireless Interface signal generally reaches beyond the average size of a home without interference or obstructions.
  • Page 12 To end setup and transfer control of the system to a homeowner, tap Transfer to Owner. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 13: Test Run

    In the kumo cloud app, tap Settings > System Setup > Installer Settings. Enter 9999 for installer login. Tap the required site and then tap Test Run. Perform the test run as explained above. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 14: Transfer To The Owner

    Tap Finish without Transfer. The system can now be controlled normally using the kumo cloud app. For more information, view the kumo cloud Owner Manual at kumocloud.com under Additional Resources. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 15: More Settings

    Tap Auto Mode or Display Offset to adjust the settings. Advanced Indoor Unit Settings To access additional settings, tap Advanced. Advanced settings will vary by indoor unit. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 16: Set Prohibits

    Note: If the unit is turned off when the Mode prohibit is active, the unit must be turned back on through the MHK2 controller, not kumo cloud. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 17: Select A Time Zone

    If the device on which the kumo cloud app is running detects a local time zone, other than the US time zones, the local time zone is also displayed as an option.Program events will occur at their set times according to the time zone selected. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 18: Accessories

    Wireless Interface to provide whole home control. To add an accessory to an existing site: Tap Accessories. Tap the Accessory you would like to connect. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 19: Add Wireless Sensor

    Program Settings The PAC-USWHS003-TH-1 Mitsubishi Electric Wireless Temperature and Humidity Sensor is a wireless sensor that is designed to provide remote sensing capabilities to the Wireless Interface. This is an optional part. One Wireless Sensor may be configured for each Wireless Interface.
  • Page 20 Ideal application temperature range is 70°F to 100°F (21°C to 38°C). To check sensor battery life or battery replacement, refer to the Owner Manual at kumocloud.com under Additional Resources. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 21: Kumo Station

    ® kumo station The PAC-WHS01HC-E, Mitsubishi Electric Equipment Controller, kumo station contains relays that allow for controls integration of third-party backup heaters, humidifiers, dehumidifiers, ventilation systems, and hydronic heaters. kumo station may be optionally wired to an indoor unit. If you choose this configuration, set up the indoor unit zone via kumo cloud before adding any kumo station accessories.

  • Page 22: Backup Heater - 2Nd Stage

    The amount of time to wait for the heat pump to raise the room temperature prior to energizing the heater. Only heat pump (not shown) The temperature above which only the heat pump runs. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 23: Backup Heater - 3Rd Stage

    If necessary, adjust the Delay, or the amount of time to wait for the Heat pump and 2nd stage heater to raise the room temperature prior to energizing the heater. Verify settings and tap Save. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 24: Dehumidifier

    Wireless Sensor. Zones with connected MHK2 controllers also appear as options in the list of zones that provide humidity readings e.g.MHK2: Living Room and Wireless Sensor: Bedroom. Tap Next. Verify settings and tap Save. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 25: Humidifier

    Wireless Sensor. Zones with connected MHK2 controllers appear as options in the list of zones that provide humidity readings e.g. MHK2: Living Room and Wireless Sensor: Bedroom. Tap Next. Verify settings and tap Save. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 26: Ventilation

    OFF: Disable the ventilation system. Select the Air Cycle to identify how many minutes out of each hour the ventilation system should be active. Tap Next. Verify settings and tap Save. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 27: Hydronic Heater

    Tap Next. Select the outdoor temperature at which the heat pump should run in tandem with the hydronic heater. Tap Next. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.
  • Page 28 Tap Cleaning Start Time and then select a start time for the cleaning cycle. The kumo cloud app then displays the hydronic heater settings that are selected. Verify the settings and tap Save. The hydronic heater is connected to the zone. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 29: Airflow For Static Pressure

    (not shown). If setting airflow while Adding an Indoor Unit, tap Save to move on to complete the Add Unit. See the Add Unit section. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 30: First Generation Wireless Interfaces

    ® The kumo cloud 2.9.1 app can be used with first-generation Wireless Interfaces (PAC-WHS01WF-E), sold in 2016 and earlier. Some features are unavailable with this older Interface. Old Interfaces and new Wireless Interfaces (PAC-USWHS002-WF-1 and PAC-USWHS002-WF-2) cannot be used together in the same kumo cloud account.

  • Page 31: Name A Zone

    Enter the Adapter ID and MAC Address found on the back of the Wireless Interface. Note: This field is case-sensitive so make sure all lower-case and capital letters are entered accurately. Tap Add Zone. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 32: Maintenance

    Tap History to view the most recent 10 errors at the site. If the equipment had errors before kumo cloud was setup, those errors will not display in History. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 33: Access Unit Settings

    Tap the name of the Zone. Add Unit To add a unit to an existing site, tap Add indoor unit. Then follow instructions in the Add Indoor Units section. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 34: Delete Unit

    Access Unit Settings Tap Auto Mode, Display Offset or Advanced. Tap the desired setting. The change is applied on the indoor unit in a few seconds. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 35: Firmware

    Turns the unit off temporarily. Settings by Number Add a setting using the number code provided in an app note or another manual. Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 36: Faqs

    Inside the Google Home app, a user can create rooms with preset or entirely custom names (numbers, punctuation, and even emojis are supported), and can then assign devices as members of these rooms. They Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.

  • Page 37: Kumo Cloud Skill With Amazon Alexa

    Skills icon. In the Search all skills box, type Mitsubishi Electric US kumo cloud and select the kumo cloud skill from the drop-down list. From the list of results displayed, click or tap Mitsubishi Electric US kumo cloud. The Enable button and the Account linking required message are displayed on the Mitsubishi Electric US kumo cloud skill page.
  • Page 38 ● Auto (or Heat-Cool) ● Off How do I control my HVAC units using the Mitsubishi Electric US kumo cloud skill after I have relabeled the Zone name(s) in my kumo cloud mobile app? If you relabeled the Zone name(s) in your kumo cloud mobile app, you have to rediscover your devices via...
  • Page 39 NOTES Specifications are subject to change without notice. © 2021 Mitsubishi Electric US, Inc.
  • Page 40 © 2021 Mitsubishi Electric US, Inc. kumo cloud is a registered trademark of Mitsubishi Electric US, Inc. iPhone, Apple and AirPort are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service of Apple Inc.

This manual is also suitable for:

Pac-uswhs002-wf-1Pac-uswhs002-wf-2

Table of Contents