Subaru B9 TRIBECA WX 2007 Manual page 737

asieps_tobira.book 9 ページ ２０１２年２月１０日 金曜日 午後３時２６分
Step
9 CHECK BODY HARNESS.
Measure the voltage between connector (R167)
and chassis ground.
Connector & terminal
(R167) No. 7 (+) — Chassis ground (– ):
10 CHECK THE BODY INTEGRATED UNIT.
Measure the voltage between connector (i84)
and chassis ground.
Connector & terminal
(i84) No. 4 (+) — Chassis ground (–):
11 CHECK COMBINATION METER.
Measure the voltage between connector (i84)
and chassis ground.
Connector & terminal
(i84) No. 20 (+) — Chassis ground (–):
12 CHECK COMBINATION METER.
Measure the voltage between connector (i11)
and chassis ground.
Connector & terminal
(i11) No. 5 (+) — Chassis ground (–):
13 CHECK SEAT BELT WARNING SYSTEM.
1) Disconnect the driver's seat belt.
2) Turn the ignition switch to ON.
14 CHECK SEAT BELT WARNING SYSTEM.
Wait for 6 seconds from the step 12 condition
(seat belt warning buzzer beeps and warning
light blinks).
15 CHECK SEAT BELT WARNING SYSTEM.
Connect the driver's seat belt buckle in the step
13 condition (seat belt warning light repeat illu-
minating/blinking every 15-seconds, and
warning buzzer beeps).
16 CHECK SEAT BELT WARNING SYSTEM.
Disconnect the driver's seat belt.
17 CHECK SEAT BELT WARNING SYSTEM.
1) Lift-up the vehicle.
NOTE:
Raise all wheels off floor.
2) Start the engine, and set the vehicle speed
to 15 km/h (9 MPH) or more.
NOTE:
When there is a speed difference between front
and rear wheels, the ABS or VDC warning may
light, but this does not indicate a malfunction.
When diagnosis is complete, perform clear
memory for VDC. <Ref. to VDC(diag)-15,
OPERATION, Subaru Select Monitor.>
18 CHECK SEAT BELT WARNING SYSTEM.
Connect the driver's seat belt in the step 16
condition.
19 SEAT BELT WARNING SYSTEM
Disconnect the driver's seat belt in the step 17
condition.
20 CHECK SEAT BELT WARNING SYSTEM.
Connect the driver's seat belt.
Seat Belt Warning System
Check
Is the voltage 10 V or more?
Also, does the seat belt warning
light come on?
Is the voltage 10 V or more?
Is the voltage 10 V or more?
Also, does the seat belt warning
light come on?
Is the voltage 10 V or more?
Also, does the seat belt warning
light come on?
Does the seat belt warning
buzzer beep and warning light
blink for 6 seconds after turning
the ignition switch to ON?
Does the seat belt warning light
repeat illuminating/blinking
every 15-seconds, and the
warning buzzer beep?
Does the seat belt warning light
go off and the buzzer stop?
Does the seat belt warning light
repeat illuminating/ blinking
every 15-seconds?
Does the seat belt warning light
repeat illuminating/ blinking
every 15-seconds?
Does the seat belt warning light
go off and the buzzer stop?
Does the seat belt warning light
repeat illuminating/ blinking
every 15-seconds?
Does the seat belt warning light
go off and the buzzer stop?
SB-9
SEAT BELT SYSTEM
Yes No
Go to step 10. Repair or replace
the driver's seat
inner belt and body
harness.
Go to step 11.
Check the body
integrated unit.
Go to step 12.
Replace the body
integrated unit.
Go to step 13. Check the combi-
nation meter.
Go to step 14. Replace the body
integrated unit.
Go to step 15. Replace the body
integrated unit.
Go to step 16. Replace the body
integrated unit.
Go to step 17. Replace the body
integrated unit.
Go to step 18.
Replace the body
integrated unit.
Go to step 19. Replace the body
integrated unit.
Go to step 20.
Replace the body
integrated unit.
A temporary Replace the body
contact failure. integrated unit.