Subaru B9 TRIBECA WX 2007 Manual page 131

asieps_tobira.book 56 ページ ２０１２年２月１０日 金曜日 午後３時２６分
AIRBAG SYSTEM (DIAGNOSTICS)
Step
1 CHECK POOR CONTACT OF CONNEC-
TORS.
Check for poor contact of the connectors
between the airbag control module and the pas-
senger's airbag module.
2 CHECK PASSENGER'S AIRBAG MODULE.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than 20
seconds.
2) Remove the console side cover lower on the
passenger's side.
3) Disconnect the connector (AB10) from
(AB9).
4) Connect the connector (1P) in the test har-
ness P to connector (AB9).
5) Connect the airbag resistor to the connec-
tors (2P) and (3P) of test harness P.
6) Connect the battery ground terminal and
turn the ignition switch to ON.
3 CHECK AIRBAG MAIN HARNESS (PASSEN-
GER'S AIRBAG HARNESS).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than 20
seconds.
2) Disconnect the airbag resistor from the con-
nectors (2P) and (3P) of test harness P.
3) Remove the instrument panel lower cover
and disconnect the connector (AB7) from
(AB2).
4) Disconnect the connector (AB6) from the
airbag control module, and connect the connec-
tor (1U) in the test harness U.
5) Measure the resistance between connector
(2U) in the test harness U and connectors (2P)
and (3P) in the test harness P.
Connector & terminal
(2U) No. 3 — (2P) No. 1:
(2U) No. 5 — (2P) No. 2:
(2U) No. 9 — (3P) No. 3:
(2U) No. 13 — (3P) No. 4:
4 CHECK AIRBAG MAIN HARNESS (PASSEN-
GER'S AIRBAG HARNESS).
Measure the resistance between connectors
(2U) in the test harness U, and between con-
nector (2U) and chassis ground.
Connector & terminal
(2U) No. 3 — (2U) No. 5:
(2U) No. 3 — Chassis ground:
(2U) No. 5 — Chassis ground:
(2U) No. 9 — (2U) No. 13:
(2U) No. 9 — Chassis ground:
(2U) No. 13 — Chassis ground:
5 CHECK AIRBAG CONTROL MODULE.
1) Connect all the connectors.
2) Erase the memory.
3) Perform the Inspection Mode.
4) Read the DTC.
Diagnostic Chart with Trouble Code
Is there poor contact?
Does the airbag warning light
illuminate for 6 seconds and go
off?
Is the resistance less than 10
Ω?
Is the resistance more than 1
MΩ?
Is the same DTC displayed?
AB(diag)-56
Check Yes
Replace the airbag
harness.
Replace the pas-
senger's airbag
module. <Ref. to
AB-15, Passen-
ger's Airbag Mod-
ule.>
Go to step 4.
Go to step 5.
Replace the airbag
control module.
<Ref. to AB-19,
Airbag Control
Module.>
No
Go to step 2.
Go to step 3.
Replace the airbag
main harness
along with body
harness.
Replace the airbag
main harness
along with body
harness.
Go to step 6.